Schumacher SC-8010A owner manual Using the built-in alternator tester, Alternator Testing Notes

Page 12

using the built-in alternator tester

This battery charger has a built-in alterna- tor tester that displays either an accurate alternator voltage or an estimate of the alternator’s relative output compared to normal alternators. The Alternator % values displayed should be taken as general reference, not precise diagnosis. The alternator tester functions the same as the battery tester (see previous sec- tion of this manual for details) with a few differences.

TESTING SEQUENCE

There are three basic steps required to use the SC-8010A as an alternator tester.

1.Connect the charger battery clamps to the battery or charging system. Be sure to follow all of the precautions listed under

“OPERATING INSTRUCTIONS”.

2.Connect the charger power cord to a 120V AC 2-prong wall outlet. Again, be sure to follow all of the precautions listed under

“OPERATING INSTRUCTIONS”.

3.Start the vehicle and turn on the vehicle’s headlights. Read the voltage on the digital display or press the digital display button to set the tester to Al- ternator % and read the alternator percent.

TESTER STATUS LEDs

When the SC-8010A is operating as an alternator tester, the status LEDs light under the following conditions.

The Charged (green) LED will light if the output of the charging system is at the normally desired level.

The CHARGING (yellow) LED does not light in the alternator test mode.

The connected LED lights if the tester detects a connection.

When the tester digital display is set to voltage, the CHARGED and CHARG-

ING LEDs won't light (it could be testing a battery or an alternator).

ALTERNATOR TESTING NOTES

The alternator percent display can range from 0 to 199.

The DIGITAL display cannot be set to Alternator % during charging.

12

Image 12
Contents Send Warranty Product Repairs to ElectronicTable of Contents Important Safety Instructions Help us help youPersonal Safety Precautions Before Using Your Battery ChargerPlugging IT Preparing your battery to be charged Charging Battery In The VehicleOperating instructions Negative Grounded System Engine Starting Notes Using your battery charger OverviewGeneral Charging Notes Battery Type Button ChargeR CONTROLsDigital Display Button Charge Start ButtonMode of Operation Control panel guideSE-8010A Control Panel Guide Digital DisplayUsing the built-in Battery tester Using the built-in alternator tester Alternator Testing NotesBattery percent and charge time Lower the reading the longer charg- ing will takeMaintenance and Care Charging tipsTroubleshooting Problem Possible Cause SolutionWarranty E C T R Ó N I C O Índice Instrucciones de Seguridad ImportantesGuarde Estas Instrucciones Advertencia Los cargadores deAyúdenos Para Poderle Precauciones DE Seguridad Personal Antes DE Usar SU Cargador DE BateríasCómo Enchufarlo EL USO DE UN Cordón DE EXTEN- SiónCómo Preparar SU Batería Para Cargarse Instrucciones DE OperaciónPara Cargar LA Batería DEN- TRO DEL Vehículo Sistema a Tierra Negativo Para Cargar LA Bateríasacada DEL VehículoCómo Usar EL Arranque DE MO- TOR. Engine Start Desulfation Mode Modo DE Desulfatar Cómo Usar SU Cargador DE BateríasVista General Notas Generales Respecto AL Proceso DE CargarBotón DE Display Mode Modo DE Pantalla Battery Type Button Botón DE Tipo DE BateríaControles DEL Cargador Charge Start Button Botón DE Comienzo DE CargaGuia AL Panel DEL Control Guia AL Panel DEL Control DEL SE-8010AEL USO DEL Probador DE Baterías Incorporado Secuencia DE ProbarProbador Y Cargador EL USO DEL Probador DE Alternadores Incorporado Notas Para Probar EL % DE BateríaNotas Sobre LA Prueba DE AL- Ternadores Porcentaje DE LA Batería Y Tiempo DE Cargar Potencia de Régimen de la BateríaPautas Para Cargar Mantenimiento Y CuidadoSolución DE Problemas Problema Posible Causa SoluciónGarantía