Ingersoll-Rand 7015-11V-A specifications INCLUDINGOPERATION,INSTALLATION& Maintenance, Capacities

OPERATOR’S MANUAL

INCLUDING:OPERATION,INSTALLATION& MAINTENANCE	Released:	2-14-91
Tool &Hoist Products “0” SERIES DIE GRINDER	Revised:	9-27-93
18,000 R.P.M.	Form:	3754-2

Model 7015-11V-A

IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

OPERATING AND SAFETY PRECAUTIONS

To aid the operator’s understanding of proper and safe use of grinders, the publications, “Use, Care and Protection of Abrasive Wheels”, A.N.S.I. 87.1 and “Safety Code for Portable Air Tools”, A.N.S.I. B186.1, can be purchased from:

American National Standards Institute, Inc.

1430 Broadway

New York, New York 10016

CAUTION, .

lKeep hands and clothing away from rotating end of tool.

lWear suitable eye protection while operating tool.

lUse tool only for purposes for which it was intended.

lDisconnect air supply from tool before removing/installing mounted wheel or performing other maintenance procedures.

lNever exceed rated r.p.m. of tool.

lUse only mounted wheels of the A, B and W shapes.

lUse only medium and high strength mounted wheels.

lDo not use excessive work pressure.

lAllow only people who have received training in “propergrind- er operation” to operate grinder.

WARNING: Repeated prolonged operator exposure to vibrations which may be generated in the use of certain hand-held tools may produce Raynaud’s phenomenon, commonly referred to as Whitefinger disease. The phenomenon produces numbness and burning sensations in the hand and may cause circulation and nerve damage as well as tissue necrosis. Repetitive users of hand-held tools who experience vibrations should closely moni- tor duration of use and their physical condition.

MOUNTING INSTRUCTIONS

Be sure collet is in good condition and property secured to grinder spindle.

Insert shaft of mounted wheel to the full depth of gripping jaws of collet. At least one-half of shaft length shall be inserted into collet jaws.

Be sure mounted wheel is compatible with the speed of the grinder.

Use type 16, 17, 18, 18R and 19 cone and plug wheels only with optional cone wheel adapter 37292-( ).

		CAPACITIES	(MAXIMUM)
l	Carbide	Bur	3/4”
l	Mounted	Stone	1-1/2”

AIR SUPPLY REQUIREMENTS

For maximum operating efficiency, the following air supply specifi- cations should be maintained to this air tool:

lAIR PRESSURE - 90 PSIG (6 bar)

lAIR FILTRATION - 50 micron l LUBRICATED AIR SUPPLY

l HOSE SIZE - 5/16” (8 mm) I.D.

An ARO® model 128231-800 air line FILTER/REGULATOR/LU- BRICATOR (F.R.L.) is recommended to maintain the above air supply specifications.

ROUTINE LUBRICATION REQUIREMENTS

Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals:

EVERY 8 HOURS OF TOOL OPERATION -Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not used, apply several drops of spindle oil (29665) in air inlet.

EVERY 40 HOURS OF TOOL OPERATION - Flush tool with a solution of three (3) parts cleaning solvent to one (1) part spindle oil (or use Kerosene).

RECOMMENDED LUBRICANTS

After disassembly is complete, all parts, except sealed or shielded bearings, should be washed with solvent. To relubricate parts, or for routine lubrication, use the following recommended lubricants:

Where	Used	ARO Part #	Description
Air Motor		29665	1 qt. Spindle Oil
“0” Rings	& Lip Seals	36460	4 oz. Stringy Lubricant
Gears and Bearings		33153	5 lb. “EP”- NLGI #1 Grease

For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand Dis- tribution Center, White House, TN at PH: (615) 672-0321, FAX: (615) 672-0601.

ARO Tool & Hoist Products
Ingersoll-Rand	Company	.
1725 U.S. No.	1 North l P.O. Box 8000 l Southern	Pines. NC 28388-8000

©1993 THE ARO CORPORATlON PRINTED IN U.S.A.