Ryobi TS1343L manual Squaring the Miter Table to the Fence, See Figures 15

Page 17

ASSEMBLY

WARNING:

Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock button when blade is rotating.

NOTE: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we can clearly show points being made in the illustra- tions. Never operate the saw without all guards securely in place and in good operating condition.

SQUARING THE MITER TABLE TO THE FENCE

See Figures 15 - 18.

Unplug the saw.

Push down on the saw arm and pull out the lock pin to release the saw arm.

Raise saw arm to its full raised position.

Loosen the miter lock handle approximately one-half turn.

Depress the miter lock plate and rotate the miter table until the scale indicator on the control arm is positioned at 0°.

Release the miter lock plate and securely tighten the miter lock handle.

Lay a framing square flat on the miter table. Place one leg of the square against the fence. Place the other leg of the square beside the throat plate in the miter table. The edge of the square and the throat plate in the miter table should be parallel as shown in figure 15.

If the edge of the framing square and the throat plate in the miter table are not parallel as shown in figures 16 and 17, adjustments are needed.

Using the blade wrench, loosen the socket head screws securing the fence. Adjust the fence left or right until the framing square and throat plate are parallel.

Retighten the screws securely and recheck the fence-to- table alignment.

FRAMING

MITER

MITER

FENCE

SQUARE

TABLE

 

SCALE

THROAT PLATE

 

INDICATOR

MITER

 

LOCK HANDLE

VIEW OF MITER TABLE SQUARE WITH FENCE

Fig. 15

FRAMING

MITER

MITER

SQUARE

FENCE

TABLE

SCALE

THROAT PLATE

 

INDICATOR

MITER

 

LOCK HANDLE

VIEW OF MITER TABLE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

Fig. 16

FRAMING

MITER

MITER

SQUARE

FENCE

TABLE

 

 

SCALE

THROAT PLATE

 

INDICATOR

MITER

 

LOCK HANDLE

VIEW OF MITER TABLE NOT SQUARE WITH FENCE,

ADJUSTMENTS ARE REQUIRED

Fig. 17

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Warranty Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Signal Meaning SymbolsDouble Insulation ElectricalElectrical Connection Extension CordsGlossary of Terms Product Specifications FeaturesAMP Motor Know Your Compound Miter SAWBevel Lock Knob Blade Wrench StorageTools Needed AAA Batteries Dust BAG Blade Wrench Loose PartsUnpacking AssemblyMounting Holes Trace HolesWork Clamp Dust BAGTighten Miter Dust BAG Exhaust PortBatteries Compartment Cover Screw Laser Line Installing Batteries in LaserAligning the Laser Guide Line See Figures 13 To Install / Replace the BladeView of Miter Table Square with Fence Squaring the Miter Table to the FenceSee Figures 15 Socket Head Screws Fence Squaring the SAW Blade to the FenceSee Figures 18 Framing Square Miter Tablemiter Lock HandleSquaring the Blade to THE MITER Table Indicator Screw Blade Scale IndicatorbevelCombination Square Miter Table Miter Lock Handle See Figures 22Applications OperationTo Cross CUT Cross CUTSee Figures 27 To Bevel CUTBevel Bevel CUTSee Figures 29 To Compound Miter CUTCompound Miter CUT Work Clamp45 X 45 Compound Miter CUT Long Workpiece Workpiece Supports To Support Long WorkpiecesPitch Number of Sides COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingCeiling Fence Right SIDE, Outside Corner Miter Table Inside FenceClamping Wide Workpieces Cutting Warped MaterialSee Figures 33 WrongPivot Adjustments Travel Pivot Adjustment AdjustmentsBevel Pivot Adjustment Positive Stop AdjustmentsLaser Adjustment Screw To Adjust the Laser GuideGeneral Maintenance MaintenanceBrush Replacement CAP Brush AssemblyService Model NO. and Serial no
Top Page Image Contents