Ryobi TS1343L Squaring the Blade to THE MITER Table, Indicator Screw Blade Scale Indicatorbevel

Page 19

ASSEMBLY

MITER SCALE

INDICATOR

SCREW

BLADE

SCALE

INDICATORBEVEL

SCALE

Fig. 22

SQUARING THE BLADE TO THE MITER TABLE

COMBINATION

SQUARE

MITER

TABLE MITER LOCK HANDLE

See Figures 22 - 25.

Unplug the saw.

Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

Loosen the miter lock handle approximately one-half turn.

Depress the miter lock plate and rotate the miter table until the scale indicator on the control arm is positioned at 0°.

Release the miter lock plate and securely tighten the miter lock handle.

Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.

Place a combination square against the miter table and the flat part of saw blade.

NOTE: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

Rotate the blade by hand and check the blade-to-table alignment at several points.

The edge of the square and the saw blade should be parallel as shown in figure 23.

If the top or bottom of the saw blade angles away from the square as shown in figures 24 and 25, adjustments are needed.

Loosen bevel lock knob.

Adjust positive stop adjustment screw to bring saw blade into alignment with the square. See “Positive Stop Adjust- ment” in the Adjustment section.

Retighten bevel lock knob. Recheck blade-to-table align- ment.

NOTE: The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0° and 45° angles.

The saw has two scale indicators, one on the bevel scale and one on the miter scale. After squaring adjustments have been made, it may be necessary to loosen the indicator screws and reset them to zero.

BEVEL

LOCK

KNOB

CORRECT VIEW OF BLADE

 

SQUARE WITH MITER TABLE

Fig. 23

BLADE

COMBINATION

MITER

 

SQUARE

TABLE

MITER

 

 

LOCK HANDLE

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 24

BLADE

COMBINATION

MITER

 

SQUARE

TABLE

MITER

LOCK HANDLE

VIEW OF BLADE NOT SQUARE WITH MITER TABLE,

ADJUSTMENTS ARE REQUIRED

Fig. 25

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Signal Meaning SymbolsExtension Cords ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications FeaturesBlade Wrench Storage Know Your Compound Miter SAWAMP Motor Bevel Lock KnobTools Needed AAA Batteries Dust BAG Blade Wrench Loose PartsTrace Holes AssemblyUnpacking Mounting HolesDust BAG Exhaust Port Dust BAGWork Clamp Tighten MiterAligning the Laser Guide Line Installing Batteries in LaserBatteries Compartment Cover Screw Laser Line See Figures 13 To Install / Replace the BladeSee Figures 15 Squaring the Miter Table to the FenceView of Miter Table Square with Fence Framing Square Miter Tablemiter Lock Handle Squaring the SAW Blade to the FenceSocket Head Screws Fence See Figures 18See Figures 22 Indicator Screw Blade Scale IndicatorbevelSquaring the Blade to THE MITER Table Combination Square Miter Table Miter Lock HandleCross CUT OperationApplications To Cross CUTBevel CUT To Bevel CUTSee Figures 27 BevelClamp To Compound Miter CUTSee Figures 29 Compound Miter CUT Work45 X 45 Compound Miter CUT Long Workpiece Workpiece Supports To Support Long WorkpiecesCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Right SIDE, Outside Corner Miter Table Inside Fence Cutting Crown MoldingLaying Molding Flat on the Miter Table Ceiling FenceWrong Cutting Warped MaterialClamping Wide Workpieces See Figures 33Positive Stop Adjustments AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentLaser Adjustment Screw To Adjust the Laser GuideCAP Brush Assembly MaintenanceGeneral Maintenance Brush ReplacementService Model NO. and Serial no
Top Page Image Contents