RIDGID MS 1065LZ manual Squaring the Blade to the Miter Table, See Figures 18, Combination

Page 17

ADJUSTMENTS

SQUARING THE BLADE TO THE MITER TABLE

See Figures 18 - 20.

￿Unplug your saw.

WARNING:

Failure to unplug your saw could result in acciden- tal starting causing possible serious personal in- jury.

￿Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

￿Loosen the miter lock handle approximately one-half turn.

￿Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0°.

￿Release the miter lock plate and securely tighten the miter lock handle.

￿Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.

￿Place a combination square against the miter table and the flat part of saw blade.

Note: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

￿Rotate the blade by hand and check the blade-to-table alignment at several points.

￿The edge of the square and the saw blade should be parallel as shown in figure 18.

￿If the top or bottom of the saw blade angles away from the square as shown in figures 19 and 20, adjustments are needed.

￿Loosen the lock nut securing positive stop adjustment screw. Also loosen bevel lock knob.

￿Adjust positive stop adjustment screw to bring saw blade into alignment with the square. See Figure 21.

￿Retighten bevel lock knob. Next, retighten lock nut se- curing the positive stop adjustment screw. Recheck blade- to-table alignment.

Note: The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0° and 45° angles.

Your saw has several scale indicators. After squaring adjustments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 17.

BEVEL

LOCK KNOB

MITER

FENCE

BLADE

MITER

 

MITER

MITER

LOCK

TABLE

COMBINATION

LOCK PLATE

HANDLE

SQUARE

CORRECT VIEW OF BLADE

SQUARE WITH MITER TABLE

Fig. 18

COMBINATION

SQUARE

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 19

COMBINATION

SQUARE

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 20

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operators Manual Introduction Table of ContentsRules for Safe Operation Safety and International SymbolsRead ALL Instructions ¥ Do not expose to rain or use in damp locationsBlade Coasts After Being Turned OFF Rules for Safe Operation Glossary of Terms for Woodworking Electrical SpecificationsDouble Insulation Electrical ConnectionTools Needed UnpackingMm Combination Wrench Combination Square Framing SquareLoose Parts List Know Your Compound Miter SAW FeaturesAMP Motor 10 IN. BladeCarrying Handle Blade Wrench / Storage AreaMiter Lock Handle Spindle Lock ButtonBevel Lock Knob Positive Stops on Miter TableElectric Brake Miter FenceDust Guide AssemblyDust BAG Work ClampTable Extension To Install BladeSquaring the SAW Blade to the Fence AdjustmentsSee Figures 13 Socket Head Screws FenceMiter Lock Plate MiterSee Figures 18 Squaring the Blade to the Miter TableBevel Lock Knob Miter Fence Blade CombinationBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentOperation ApplicationsCrosscutting Cutting with Your Compound Miter SAWTo Crosscut with Your Miter SAW Straight Crosscut Work ClampAT 48º Bevel CUTAT 45º Bevel CUTCompound Miter CUT Work Clamp Compound Miter CUTTo Make a Compound CUT with Your Miter SAW 45 X 45 Compound Miter CUT Long Workpiece Workpiece Supports Support Long WorkpiecesPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialWrong RightOperation Laser GuideAlignment Blade Laser GuideDo not attempt to activate the laser Changing the BatteriesLubrication MaintenanceGeneral DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the Limited Three Year Warranty HOW to Obtain Service What is not CoveredModel No MS1065LZ Serial No Customer Service Information
Top Page Image Contents