Ryobi R10630 specifications Operation, To Charge

Page 8

OPERATION

WARNING:

Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.

WARNING:

Do not allow familiarity with your circular saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

CHARGING BATTERY PACK WITH CHARGER PART NUMBER 1400667

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until light on front of charger changes from red to green.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (cutting followed by recharging) for them to become fully charged.

TO CHARGE

Connect charger to power supply.

Charge battery pack only with the charger provided.

Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only.

Connect charger to power supply.

Place battery pack in charger aligning raised rib in charger with groove in battery pack.

Press down on battery pack to be sure contacts on battery pack engage properly with charger contacts.

Normally, the yellow and green lights on charger will come on. This indicates charger is in soft start mode and should switch to fast charge mode within 5 minutes. When charger is in fast charge mode the red light will come on. If after a period of 15 minutes the yellow and green lights remain on, remove battery pack, wait 1 minute and reinsert battery pack in charger. If the yellow and green lights continue to remain on after an additional 15 minutes, the battery pack is damaged and will not accept a charge. Return battery pack to your nearest Ryobi Authorized Service Center for checking or replac- ing.

When your battery pack becomes fully charged, the red light will turn OFF and the green light will turn ON.

After normal usage, 1 hour of charging time is required to be

fully charged. A minimum charge time of 1-1/2 hours is required to recharge a completely discharged tool.

The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature.

When the batteries become fully charged, unplug your charger from power supply and remove the battery pack.

LED FUNCTION OF CHARGER

LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK:

Red LED Lighted = Fast Charging Mode.

Green LED Lighted = Fuly Charged Or In Slow Charging Mode To Maintain Battery Pack.

Yellow and Green LED Lighted = Soft Start Mode, or After 1/2 Hour Equals Hot or Defective Battery Pack.

IMPORTANT INFORMATION FOR RECHARG- ING HOT BATTERIES USING CHARGER PART NUMBER 1400667

See Figure 2.

When using your circular saw continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes be- fore attempting to recharge. When the battery pack be- comes discharged and is hot, this will cause the yellow and green lights on your battery charger to come on instead of the red light. The yellow and green lights indicate soft start mode and will switch to green only, indicating slow charge mode. The red light indicates fast charge mode, 1 hour charge time. The green light indicates slow charge mode, requiring overnight charging for batteries to reach full charge. If the green light comes on after letting battery pack cool down, remove it from charger for additional cooling.

Once the battery pack cools down, it will recharge battery pack in fast charging mode as normal.

Do not leave a hot battery pack in charger until it cools down. The green light will not go off when battery pack cools. If fast charge mode is desired, you must physically remove a hot battery pack from the charger, let it cool, then place it back in charger after it has cooled down.

NOTE: This situation only occurs when continuous use of your saw causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARG-

ING BATTERY PACK WITH CHARGER PART NUMBER 1400667" for normal recharging of batteries. If the charger does not charge your battery pack under normal circum- stances, return both the battery pack and charger to your nearest Ryobi Authorized Repair Center for electrical check.

Page 8

Image 8
Contents Operators Manual Thank YOU for Buying a Ryobi Cordless Circular SAWUnpacking Table of ContentsAccessories Read ALL Instructions Symbol Meaning Safety Alert SymbolRules for Safe Operation Important Safety Instructions for Charger Important Safety Rules for Battery ToolsDo not Charge Battery Tool in a Damp or WET Location When Servicing USE only Identical Replacement PartsImportant Safety Instructions for Circular Saws Lower Blade GuardFeatures SwitchKnow Your Cordless Circular SAW ApplicationsRED Light on Charger Part NumberCharger Operation To ChargeOperation To Install Battery Pack To Assemble or Remove BladeTo Remove Blade SAW BladesBlade Guard System Kickback Kickback is Caused byTo Lessen the Chance of Kickback KickbackStarting a CUT Depth of CUT AdjustmentTo Adjust Blade Depth To Help Maintain Control RIP Cuts Base Assembly To Cross CUT or RIP CUTWidth of CUT Scale TOP View of SAW Guideline Front of SAW Blade Guide NotchGuard To Adjust Bevel SettingBlade Guide Notch Guideline To Adjust Positive 0 Bevel StopTo Check To Pocket CUTTo RIP CUT To Assemble Optional RIP GuideBatteries MaintenanceBattery Pack Removal and Preparation for Recycling Ryobi Cordless Circular SAW Model Number R10630 Parts List 2 in. Cordless Circular SAW Model NO. R10630

R10630 specifications

The Ryobi R10630 is a standout model in the realm of power tools, particularly appealing to DIY enthusiasts and professionals alike. This versatile tool combines innovative technology with practical features, making it a valuable addition to any toolbox.

One of the main highlights of the Ryobi R10630 is its powerful motor. Equipped with a robust 10 amp motor, this tool delivers impressive performance for various applications, including cutting, sanding, and drilling tasks. The motor ensures that users can tackle tougher materials with ease, making it suitable for a wide range of projects.

Another significant feature of the R10630 is its lightweight design. Weighing in at just under eight pounds, this tool is easy to handle, reducing user fatigue during longer projects. The ergonomic design also enhances comfort, allowing for extended use without discomfort.

The Ryobi R10630 incorporates advanced technologies that elevate its functionality. The tool is equipped with an electronic speed control system, allowing users to adjust the speed settings easily, depending on the materials they are working with. This feature ensures that users achieve optimal results, whether they are working with softwoods, hardwoods, or metal.

Safety is also a priority in the design of the R10630. It includes a safety lock-off switch, preventing accidental operation, which is crucial for ensuring user protection during use. Additionally, the onboard LED work light illuminates the work area, providing better visibility and enhancing precision, especially in dimly lit spaces.

Durability is another significant characteristic of the Ryobi R10630. Crafted from high-quality materials, it is designed to withstand rigorous use over time. Its sturdy construction ensures longevity, making it a reliable tool that users can depend on for years to come.

The Ryobi R10630's versatility sets it apart from its competitors. With multiple attachments available, users can easily switch between tasks, ranging from sanding surfaces to making precise cuts. This adaptability makes it a favorite among both hobbyists and professionals who require a tool that can meet various demands.

Overall, the Ryobi R10630 brilliantly combines power, comfort, and adaptability. With its advanced features and robust construction, it stands out as a top choice for anyone looking to enhance their woodworking and DIY capabilities. Whether you are a seasoned professional or just starting, the R10630 proves to be an invaluable asset in achieving high-quality results.