Chicago Electric 94488 operating instructions Troubleshooting, Please Read the Following Carefully

Page 17

TROUBLESHOOTING

Problem

 

Possible Solution

 

1.

Check for amount of fuel.

 

2.

Make sure Choke Lever is in proper position.

 

3.

Make sure Spark Plug Wire is not loose.

 

4.

Check condition of Spark Plug. Wipe off any access fuel

 

 

with a clean, dry cloth. Prior to reinstalling the spark

 

 

plug, vent the combustion chamber by pulling the start

 

 

grip several times.

Engine will not start or runs

5. Make sure Air Filter assembly is clean

poorly.

6.

Make sure to press Decompression Valve before

 

 

 

starting. Clean/replace valve if it pops up without being

 

 

pulled when unit is off.

 

7.

Have a qualified service technician check the ignition

 

 

system.

 

8.

Have a qualified technician check/adjust the carburetor.

 

 

The carburetor is not set to run satisfactorily at

 

 

altitudes above 5,000 ft.

Engine smokes excessively

1. Check for proper mix of fuel.

when running.

2. Check Air Filter condition.

 

1.

Check for proper mix and amount of fuel.

Saw Blade not rotating up

2. Check condition of Spark Plug.

to full speed.

3. Adjust tension on V-Belt.

 

4.

Check Air Filter.

Poor quality of cut.

1.

Make sure Blade is undamaged.

2.

Make sure Saw Blade is properly installed.

 

Kill Switch does not turn off

Immediately discontinue use of Cut Off Saw. Have a

Engine.

qualified service technician check the Kill Switch.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER AS- SUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGI- NAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

REV 07e

SKU 94488

For technical questions, please call 1-800-444-3353

PAGE 17

Image 17
Contents GAS Portable CUT OFF SAW Your Warranty Is Voided IfGeneral Safety Rules and Precautions Product SpecificationsSave this Manual Work AreaTool USE and Care Personal SafetyIndustrial applications must follow Osha guidelines ServiceFire and Explosion Precautions Chemical Precautions Mechanical PrecautionsNoise Precaution SAW Blade PrecautionsKickback Precautions Push the Saw Blade past the workpiece prior to release MISC. PrecautionsSee Figure A, page 11, for details Product FeaturesUnpacking REV 07e Figure a See Figure a Assembly InstructionsPRE-START Instructions Table a Operating InstructionsTo Stop The Cut Off Saw See Figure BSee Figure C INSPECTION, MAINTENANCE, and CleaningSee Figure E Figure CFigure E Please Read the Following Carefully TroubleshootingPart Description ’ty Parts LIST/ASSEMBLY Diagram Crankshaft Housing AssemblyParts LIST/ASSEMBLY Diagram Crankshaft & Piston Assembly Part Description Qty Parts LIST/ASSEMBLY Diagram Cylinder & Muffler Assembly18C 16C 13C 19C 17C 12C 15C 11C 3C 4C 23C 24C Parts LIST/ASSEMBLY Diagram Fuel Tank & CarburetorParts LIST/ASSEMBLY Diagram Handle & Main Cover Assembly 15E 14E 13E 12E 10E 7E 8E 16E Parts LIST/ASSEMBLY Diagram AIR Filter AssemblyBolt M8 x Screw M5 x Washer Wheel Support 10G Wheel Shaft Parts LIST/ASSEMBLY Diagram Front Handle & Support AssemblyEmission Control System Warranty Consequential Damages Coverage