Kawasaki RH1-090048 Charge Battery Pack, Operating the Worklight, Operating the on / OFF Switch

Page 18

 

CHARGING BATTERY PACK

CHARGE BATTERY PACK:

BATTERY PACK

1.

Plug the charger into

 

 

the nearest 120 volt

 

 

electrical outlet.

 

2.

Make sure the trigger

 

 

on the Cordless Worklight

LED

 

is in the “OFF” position

 

LIGHT

 

and remove the battery

 

 

pack from the Worklight.

 

3.

Insert the battery pack into

 

 

the charger. Be sure that the

BATTERY

 

battery pack is fully seated

OPERATING THE WORKLIGHT

Parts of this Worklight heat up almost immediately when in use. To avoid burns, use caution when handling light bulb and metal reflector. Never change a hot light bulb. Bulb must be cool to the touch before attempting to remove or replace it.

OPERATING THE ON / OFF SWITCH

Press the “ON/OFF” switch to turn the worklight “ON” and “OFF”.

ADJUSTING THE WORKLIGHT BEAM

in the charger.

CHARGER

 

Do not force.

4.The red indicator light should come “ON” indicating that the battery pack is in a “Fast Charge” mode. If the green indicator light comes “ON”, then the battery is already fully charged.

5.After approximately one hour of charging, the red indicator light should go “OFF” and the green light should come “ON” indicating that the battery is fully charged and the charger is now in a “Trickle Charge” mode.

6.The battery can be left in a “Trickle Charge” mode until ready to use.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES

Hold the handle of the Worklight securely in one hand. With the other hand, swivel the head of the Worklight counter-clockwise until it is at the angle you desire. Swivel the head of the Worklight clockwise to return it to its original position.

UP

DOWN

When using your Worklight continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the red light on the charger will flash. When the battery pack cools down, the red light will glow continuously to indicate fast charging mode, 1-hour charge time.

This will occur when continuous use of your Worklight causes the battery pack to become hot. It does not occur under normal circumstances.

REPLACING THE LIGHT BULB

This Worklight uses a Krypton 18V, 0.3A light bulb. Use of any other kind of light bulb may cause damage or injury.

Parts of this worklight heat up almost immediately when in use. To avoid burns, use caution when handling light bulb and metal reflector. Never change a hot light bulb. Bulb must be cool to the touch before attempting to remove or replace it.

9

10

Image 18
Contents 19.2V 2-SPEED BATTERY-OPERATED Drill Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsPersonal Safety Important SafeguardsElectrical Safety Save These Instructions for Future ReferenceSafety Rules for Cordless Drill / Drivers ServiceSpecific Safety Rules AND/OR Symbols Tool USE and CareAccessories SymbolsSymbol Name Explanation Functional DescriptionRemove Battery Pack BatteryREMOVING/ATTACHING Battery Pack Attach Battery PackInstalling Drill BIT Into Keyless Chuck Charging Battery PackAssembly Important Information for Recharging HOT BatteriesForward / Reverse and Trigger Lock Lever Variable Speed Trigger SwitchTorque Settings HIGH/LOW Speed Gear ShiftingDrilling Masonry Maintenance and CleaningDrilling Metal Drilling WoodConductor Size in A.W.G AccessoriesSpecifications Protecting the EnvironmentYear Limited Warranty Commercial or Rental PurposeWarranty Disclaimers 19.2V BATTERY-OPERATED Worklight Safety Rules for Worklight Symbols Battery Tool USE and Care Safety Rules for WorklightControls and Components Component Model NumberRemoving / Attaching Battery Pack Adjusting the Worklight Beam Charge Battery PackOperating the on / OFF Switch Operating the WorklightRecommended Sizes of Extension Cords 120 Volt AC 60 HZ Tools Tool Current RatingCorded and Cordless Multi-Purpose Tools Exclusions 19.2V Battery Pack Congratulations Symbols Year Limited Home USE Warranty Which Extend Beyond the Description on the Face HereofWarranty Disclaimers 19.2V BATTERY-OPERATED Circular SAW Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsSave These Instructions for Future Reference Important SafeguardsElectrical Safety Work AreaSpecific Safety Rules AND/OR Symbols Personal SafetyService Tool USE and CareSafety Rules for Circular SAW Causes and Prevention of KickbackFunctional Description SymbolsSymbol Name Explanation Component Model NumberBlade Safety Lock Button Control FeaturesBattery Bevel Leveling KnobRemoving / Attaching Battery Pack Charging Battery PackCharger Assembly Adjusting Depth and AngleAttaching / Removing Blade Operating the Circular SAW Operating the Trigger SwitchTrigger Switch General CuttingSpecifications Maintenance and CleaningAccessories Tool Current RatingYear Limited Warranty Commercial or Rental PurposeWarranty Disclaimers 19.2V BATTERY-OPERATED Reciprocating SAW General Safety RULES-FOR ALL Battery Operated Tools Important Safeguards Safety Rules for Cordless Reciprocating Saws Name Explanation Functional Description Battery Controls and ComponentsCordless Reciprocating Saw To Attach Blade Variable Speed Trigger SwitchThis Tool is Controlled by a Trigger Switch To Remove BladePlunge Cutting Metal CuttingVoltage 19.2V Length of Stroke 22mm 7/8 Switch Other Consumer DO-IT-YOURSELF DIY Tools Limitation Of Liability