Kawasaki RH1-090048 manual Recommended Sizes of Extension Cords 120 Volt AC 60 HZ Tools

Page 19

For your convenience, a spare light bulb is included inside the unit. Unscrew the rim and carefully remove it from the light assembly.

Equipment service must be performed only by qualified repair personnel using authorized replacement parts. Service or maintenance by unqualified personnel could result in considerable risk of personal injury. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

1.Remove the battery pack from the Worklight.

2.Hold the top of the Worklight with one hand while twisting the rim in a counter-clockwise direction with the other. Continue turning until the rim comes loose.

3.Remove the bulb by turning it slightly and pulling it out of the bulb fitting. Be careful not to damage the delicate parts inside the case.

4.Insert the new bulb, then carefully put the rim back in place and turn it clockwise to tighten it.

REPLACEMENT BULB

ACCESSORIES

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool.

Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.

If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive voltage drop or overheating. The smaller the gauge number, the heavier the cord (see table below).

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS

TOOL CURRENT RATING

 

CONDUCTOR SIZE IN A.W.G

 

AMPERE

10FT.

25FT.

50FT.

100FT.

3-6

18

18

18

18

MAINTENANCE AND CLEANING

Always remove the battery pack before attempting cleaning or maintenance.

Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the casing. Never immerse any part of the tool in a liquid. Always keep the ventilation openings clear.

Always clean the battery pack using only a dry cloth. Do not use liquids. Always unplug the charger before cleaning it.

Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth.

Never open the Worklight case, battery pack or charger. Do not attempt to repair the Worklight, battery pack or charger yourself. Opening any of these parts will void your warranty.

Use only authorized replacement parts for your tool.

6-8

18

18

18

16

8-10

18

18

18

14

10-12

16

16

14

14

12-16

14

12

12

-

16-20

12

12

12

-

SPECIFICATIONS

SPECIFICATIONS

 

 

 

Voltage

19.2V

 

 

 

 

Light Bulb Type

Krypton 18V 0.3A

Charger Input

120V

 

60Hz

Charging Time

Approx. 1 Hour

Battery Type

Ni-Cad

 

 

11

12

Image 19
Contents 19.2V 2-SPEED BATTERY-OPERATED Drill Congratulations Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools Recognize Safety SYMBOLS, Words and LabelsSave These Instructions for Future Reference Important SafeguardsElectrical Safety Personal SafetyTool USE and Care ServiceSpecific Safety Rules AND/OR Symbols Safety Rules for Cordless Drill / DriversFunctional Description SymbolsSymbol Name Explanation AccessoriesAttach Battery Pack BatteryREMOVING/ATTACHING Battery Pack Remove Battery PackImportant Information for Recharging HOT Batteries Charging Battery PackAssembly Installing Drill BIT Into Keyless ChuckHIGH/LOW Speed Gear Shifting Variable Speed Trigger SwitchTorque Settings Forward / Reverse and Trigger Lock LeverDrilling Wood Maintenance and CleaningDrilling Metal Drilling MasonryProtecting the Environment AccessoriesSpecifications Conductor Size in A.W.GCommercial or Rental Purpose Year Limited WarrantyWarranty Disclaimers 19.2V BATTERY-OPERATED Worklight Safety Rules for Worklight Symbols Safety Rules for Worklight Battery Tool USE and CareComponent Model Number Controls and ComponentsRemoving / Attaching Battery Pack Operating the Worklight Charge Battery PackOperating the on / OFF Switch Adjusting the Worklight BeamTool Current Rating Recommended Sizes of Extension Cords 120 Volt AC 60 HZ ToolsCorded and Cordless Multi-Purpose Tools Exclusions 19.2V Battery Pack Congratulations Symbols Which Extend Beyond the Description on the Face Hereof Year Limited Home USE WarrantyWarranty Disclaimers 19.2V BATTERY-OPERATED Circular SAW Congratulations Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools Recognize Safety SYMBOLS, Words and LabelsWork Area Important SafeguardsElectrical Safety Save These Instructions for Future ReferenceTool USE and Care Personal SafetyService Specific Safety Rules AND/OR SymbolsCauses and Prevention of Kickback Safety Rules for Circular SAWComponent Model Number SymbolsSymbol Name Explanation Functional DescriptionBevel Leveling Knob Control FeaturesBattery Blade Safety Lock ButtonCharging Battery Pack Removing / Attaching Battery PackCharger Adjusting Depth and Angle AssemblyAttaching / Removing Blade General Cutting Operating the Trigger SwitchTrigger Switch Operating the Circular SAWTool Current Rating Maintenance and CleaningAccessories SpecificationsCommercial or Rental Purpose Year Limited WarrantyWarranty Disclaimers 19.2V BATTERY-OPERATED Reciprocating SAW General Safety RULES-FOR ALL Battery Operated Tools Important Safeguards Safety Rules for Cordless Reciprocating Saws Name Explanation Controls and Components Functional Description BatteryCordless Reciprocating Saw To Remove Blade Variable Speed Trigger SwitchThis Tool is Controlled by a Trigger Switch To Attach BladeMetal Cutting Plunge CuttingVoltage 19.2V Length of Stroke 22mm 7/8 Switch Other Consumer DO-IT-YOURSELF DIY Tools Limitation Of Liability