Kawasaki RH1-090048 manual Cordless Reciprocating Saw

Page 46
BATTERY
CHARGER

REMOVING / ATTACHING BATTERY PACK

REMOVE BATTERY PACK: 1. Press both release

buttons on either side of the Cordless Reciprocating Saw to release the battery pack.

2. Pull battery pack free of

RELEASE

Cordless Reciprocating Saw.

ATTACH BATTERY PACK:

BUTTON

 

1. Align the raised portion of the battery

pack with the groove in the battery com-

partment of the Cordless Reciprocating Saw.

CHARGE BATTERY PACK:

1.Plug the charger into the nearest 120 volt electrical outlet.

2.Make sure the trigger on the Cordless Reciprocating Saw is in the “OFF” position and remove the battery pack from the Cordless Reciprocating Saw.

CHARGING BATTERY PACK

BATTERY PACK

LED

LIGHT

2. Press the battery pack into place. Make sure the latches are securely fastened. Do

not use the Cordless Reciprocating Saw if the battery pack is not seated properly.

CHARGER

Before using battery charger, please read carefully all instructions and cautionary markings on battery charger, battery pack and product using battery.

Use only the charger which accompanied your product or direct replacement as listed in this manual. Do not substitute any other charger. Use only Alltrade approved chargers with your product.

Do not disassemble charger.

Do not use charger if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid.

The battery pack and charger heat during charging. Place the charger on a flat, non-flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack.

When the battery pack requires recharging, a 1 hour charge allows the tool to operate at full power. A charging indicator light on the charger will illuminate to show that charging is taking place.

3.Insert the battery pack

into the charger. Be sure that the battery pack is fully seated in the charger. Do not force.

4.The red indicator light should come “ON” indicating that the battery pack is in a “Fast Charge” mode. If the green indicator light comes “ON”, then the battery is already fully charged.

5.After approximately one hour of charging, the red indicator light should go “OFF” and the green light should come “ON” indicating that the battery is fully charged and the charger is now in a “Trickle Charge” mode.

6.The battery can be left in a “Trickle Charge” mode until ready to use.

IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES

When using your Cordless Reciprocating Saw continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the red light on the charger will flash. When the battery pack cools down, the red light will glow continuously to indicate fast charging mode, 1-hour charge time.

This will occur when continuous use of your Cordless Reciprocating Saw causes the battery pack to become hot. It does not occur under normal circumstances.

11

12

Image 46
Contents 19.2V 2-SPEED BATTERY-OPERATED Drill Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsPersonal Safety Important SafeguardsElectrical Safety Save These Instructions for Future ReferenceSafety Rules for Cordless Drill / Drivers ServiceSpecific Safety Rules AND/OR Symbols Tool USE and CareAccessories SymbolsSymbol Name Explanation Functional DescriptionRemove Battery Pack BatteryREMOVING/ATTACHING Battery Pack Attach Battery PackInstalling Drill BIT Into Keyless Chuck Charging Battery PackAssembly Important Information for Recharging HOT BatteriesForward / Reverse and Trigger Lock Lever Variable Speed Trigger SwitchTorque Settings HIGH/LOW Speed Gear ShiftingDrilling Masonry Maintenance and CleaningDrilling Metal Drilling WoodConductor Size in A.W.G AccessoriesSpecifications Protecting the EnvironmentYear Limited Warranty Commercial or Rental PurposeWarranty Disclaimers 19.2V BATTERY-OPERATED Worklight Safety Rules for Worklight Symbols Battery Tool USE and Care Safety Rules for WorklightControls and Components Component Model NumberRemoving / Attaching Battery Pack Adjusting the Worklight Beam Charge Battery PackOperating the on / OFF Switch Operating the WorklightRecommended Sizes of Extension Cords 120 Volt AC 60 HZ Tools Tool Current RatingCorded and Cordless Multi-Purpose Tools Exclusions 19.2V Battery Pack Congratulations Symbols Year Limited Home USE Warranty Which Extend Beyond the Description on the Face HereofWarranty Disclaimers 19.2V BATTERY-OPERATED Circular SAW Recognize Safety SYMBOLS, Words and Labels Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools CongratulationsSave These Instructions for Future Reference Important SafeguardsElectrical Safety Work AreaSpecific Safety Rules AND/OR Symbols Personal SafetyService Tool USE and CareSafety Rules for Circular SAW Causes and Prevention of KickbackFunctional Description SymbolsSymbol Name Explanation Component Model NumberBlade Safety Lock Button Control FeaturesBattery Bevel Leveling KnobCharging Battery Pack Removing / Attaching Battery PackCharger Adjusting Depth and Angle AssemblyAttaching / Removing Blade Operating the Circular SAW Operating the Trigger SwitchTrigger Switch General CuttingSpecifications Maintenance and CleaningAccessories Tool Current RatingYear Limited Warranty Commercial or Rental PurposeWarranty Disclaimers 19.2V BATTERY-OPERATED Reciprocating SAW General Safety RULES-FOR ALL Battery Operated Tools Important Safeguards Safety Rules for Cordless Reciprocating Saws Name Explanation Functional Description Battery Controls and ComponentsCordless Reciprocating Saw To Attach Blade Variable Speed Trigger SwitchThis Tool is Controlled by a Trigger Switch To Remove BladePlunge Cutting Metal CuttingVoltage 19.2V Length of Stroke 22mm 7/8 Switch Other Consumer DO-IT-YOURSELF DIY Tools Limitation Of Liability