Siemens SINVERT 350 Safety instructions, Qualified personnel, Proper handling, Trademarks

Page 3

Safety instructions

These Operating Instructions contain information which you should observe to ensure your own personal safety as well as to protect the product and connected equipment. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol. Notices referring only to equipment damage have no safety alert symbol. Warnings are shown in descending order according to the degree of danger as follows.

DANGER

indicates that death or serious injury will result if proper precautions are not taken.

WARNING

indicates that death or serious physical injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol indicates that damage to property may result if proper precautions are not taken.

CAUTION

indicates that an unwanted result or state may occur if the relevant instruction is not observed.

In the event of a number of levels of danger prevailing simultaneously, the warning corresponding to the highest level of danger is always used. A warning that uses a safety alert symbol indicating possible personal injury may also include a warning relating to material damage.

Qualified personnel

The associated equipment / system may only be set up and operated in conjunction with this documentation. The equipment / system may only be commissioned and operated by qualified personnel. For the purpose of the safety information in these Operating Instructions, a "qualified person" is someone who is authorized to energize, ground, and tag equipment, systems, and circuits in accordance with established safety procedures.

Proper handling

Note the following:

WARNING

The equipment may only be used for single-purpose applications explicitly described in the catalog and in the technical description, and only in conjunction with third-party devices and components approved by Siemens. This product can only function correctly and safely if it is transported, stored, set up, and installed correctly, and operated and maintained as recommended.

Trademarks

All names shown with the trademark symbol ® are registered trademarks of Siemens AG. Third parties using for their own purposes any other names in this document which refer to trademarks might infringe upon the rights of the trademark owners.

Disclaimer of liability

We have checked that the contents of this document correspond to the hardware and software described. However, since deviations cannot be precluded entirely, we cannot guarantee full consistency. The information given in this publication is reviewed at regular intervals and any corrections that might be necessary are made in the subsequent editions.

Siemens AG

A5E

Copyright © Siemens AG 2009

 

Ⓟ 12/2009

Subject to change

Image 3
Contents Sinvert Photovoltaic Trademarks Safety instructionsQualified personnel Proper handlingContents Figures TablesIntroduction About this documentationScope of validity History Chapter ContentsTarget group Document structureApplication DescriptionCommissioning the inverter Instructions and safety informationFive safety rules in Germany Hardware operationSwitching off and disconnecting the power supply Switching on Operator panel Operating the inverterPin Signal Operating mode Switching the inverter on and offLocal/Remote selector switch Grid LED indicator bar Fault resetDisplaying currently active alarms and faults Adjusting the voltageStandby operation LED Standby Maximum Power Point LED MPPAutomatic mode / Test mode Fault displayPPsolar Communication with the inverter1 WEB’log WinCCRed System components are malfunctioning Control Panel PPsolar Oscilloscope function PPsolar Device Information SINVERT-SettingsActual values Actual Value SummaryWeather conditions PV GeneratorMains Interface Data Storage PPsolar Energy10 Analysis window PPsolar Fault display / messages Alarm and fault messagesFault handling Fault typesAlarm and fault messages Meaning CategoryMain cause LED Differences in potential in the PV field Faults Causes/diagnostics/remedial measuresDiagnostics CausesMeasures Heat generation is exceeding tolerance Fault in measured-value sensingCondition Causes Cooling system is not working properlyCauses Inlet air temperature too high No checkback signal from the AC contactor Causes No power supply for Fast OFFCauses No line voltage for Fast OFF Causes Measured DC voltage is too high13 Fault Alarm Vce monitor has responded 16 Fault Alarm Direct current too high Causes Contact in the signaling circuit is open Remedial Possible24 Fault Alarm Grid voltage outside tolerance Alarm without fault Contact addresses SupportGermany
Related manuals
Manual 42 pages 49.56 Kb

350, SINVERT 350 specifications

The Siemens SINVERT 350 series is a high-performance, lightweight inverter system designed to optimize energy conversion in solar power applications. With a power rating of up to 350 kW, this inverter model is tailored for large-scale photovoltaic installations and commercial applications. Its key features and technological innovations make it a valuable addition to any renewable energy project.

One of the main features of the SINVERT 350 is its advanced grid management capability. The inverter is equipped with sophisticated monitoring systems that ensure compliance with various grid connection standards, enhancing stability and reliability for the operator. This ensures seamless integration with existing power grids while optimizing energy yield. Additionally, it supports various grid support functionalities, helping maintain grid stability during high-demand periods.

Another notable characteristic is its modular design. The SINVERT 350 allows for easy integration with other units, scaling effectively to meet the power needs of larger installations. This modularity not only enhances flexibility but also simplifies maintenance and reduces operational costs over time. Each unit can be easily accessed, which minimizes downtime during servicing.

The SINVERT 350 also features advanced cooling technology. With its robust thermal management system, the inverter operates efficiently even under high temperatures, ensuring longevity and reliability. The design minimizes losses due to heat, effectively enhancing the overall energy conversion efficiency.

In terms of safety, the SINVERT 350 is built with integrated protection mechanisms, including over-voltage and short-circuit protections. These safety features safeguard both the inverter and the connected photovoltaic modules, ensuring a secure operating environment.

Another highlight is the inverter’s compatibility with the Siemens Smart Grid solutions. This integration means users can access comprehensive monitoring and analytics tools, enabling real-time performance tracking and optimization of energy output. With built-in web-based connectivity, operators can manage the system remotely, gaining insights and facilitating proactive maintenance.

In conclusion, the Siemens SINVERT 350 series combines robust performance, innovative technologies, and reliable safety features to create a compelling choice for large-scale solar energy projects. Its advanced design ensures operational efficiency and adaptability, thereby enhancing the overall viability of solar energy as a sustainable power source.