Siemens SINVERT 350 manual Switching on

Page 11

Hardware operation

3.1 Commissioning the inverter

3.1.3Switching on

The inverter is switched on in the same way as it is switched off, but in the reverse sequence.

1.Check that all connections have been made correctly (including polarity).

2.Switch on the junction boxes in the PV field.

3.Switch on the external power supply for the medium-voltage switchgear.

4.Switch on the external power supply for the inverter container.

5.Close the medium-voltage breaker.

oOpen the grounding switch.

oClose the switch disconnector. o Close the circuit breaker.

o Note: Depending on the type of MV switchgear installed, the step sequence might vary.

6.Close the DC fuse switch disconnectors in all inverters.

7.Close the AC fuse switch disconnectors in all inverters.

8.Unlock the "Fast Stop" button.

9.Turn the keyswitch on all inverters from "Auto" to "Test" and back to "Auto" in order to reset settings.

10.If insolation levels are sufficiently high, the system will restart automatically after 30 minutes.

11.To start the system immediately, you must turn the keyswitch on the master to the test position. Then press the internal key "S111".

12.The DC contactors are automatically closed one after the other. The inverter is then started and the AC contactor is immediately closed. Now turn the keyswitch to "Auto".

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Sinvert Photovoltaic Trademarks Safety instructionsQualified personnel Proper handlingContents Figures TablesScope of validity IntroductionAbout this documentation History Chapter ContentsTarget group Document structureApplication DescriptionCommissioning the inverter Instructions and safety informationFive safety rules in Germany Hardware operationSwitching off and disconnecting the power supply Switching on Operator panel Operating the inverterPin Signal Local/Remote selector switch Operating modeSwitching the inverter on and off Grid LED indicator bar Fault resetDisplaying currently active alarms and faults Adjusting the voltageStandby operation LED Standby Maximum Power Point LED MPPAutomatic mode / Test mode Fault displayPPsolar Communication with the inverter1 WEB’log WinCCRed System components are malfunctioning Control Panel PPsolar Oscilloscope function PPsolar Device Information SINVERT-SettingsActual values Actual Value SummaryMains Interface Weather conditionsPV Generator Data Storage PPsolar Energy10 Analysis window PPsolar Fault display / messages Alarm and fault messagesFault handling Fault typesMain cause Alarm and fault messagesMeaning Category LED Differences in potential in the PV field Faults Causes/diagnostics/remedial measuresMeasures DiagnosticsCauses Heat generation is exceeding tolerance Fault in measured-value sensingCondition Causes Cooling system is not working properlyCauses Inlet air temperature too high No checkback signal from the AC contactor Causes No power supply for Fast OFFCauses No line voltage for Fast OFF Causes Measured DC voltage is too high13 Fault Alarm Vce monitor has responded 16 Fault Alarm Direct current too high Causes Contact in the signaling circuit is open Remedial Possible24 Fault Alarm Grid voltage outside tolerance Alarm without fault Contact addresses SupportGermany
Related manuals
Manual 42 pages 49.56 Kb

350, SINVERT 350 specifications

The Siemens SINVERT 350 series is a high-performance, lightweight inverter system designed to optimize energy conversion in solar power applications. With a power rating of up to 350 kW, this inverter model is tailored for large-scale photovoltaic installations and commercial applications. Its key features and technological innovations make it a valuable addition to any renewable energy project.

One of the main features of the SINVERT 350 is its advanced grid management capability. The inverter is equipped with sophisticated monitoring systems that ensure compliance with various grid connection standards, enhancing stability and reliability for the operator. This ensures seamless integration with existing power grids while optimizing energy yield. Additionally, it supports various grid support functionalities, helping maintain grid stability during high-demand periods.

Another notable characteristic is its modular design. The SINVERT 350 allows for easy integration with other units, scaling effectively to meet the power needs of larger installations. This modularity not only enhances flexibility but also simplifies maintenance and reduces operational costs over time. Each unit can be easily accessed, which minimizes downtime during servicing.

The SINVERT 350 also features advanced cooling technology. With its robust thermal management system, the inverter operates efficiently even under high temperatures, ensuring longevity and reliability. The design minimizes losses due to heat, effectively enhancing the overall energy conversion efficiency.

In terms of safety, the SINVERT 350 is built with integrated protection mechanisms, including over-voltage and short-circuit protections. These safety features safeguard both the inverter and the connected photovoltaic modules, ensuring a secure operating environment.

Another highlight is the inverter’s compatibility with the Siemens Smart Grid solutions. This integration means users can access comprehensive monitoring and analytics tools, enabling real-time performance tracking and optimization of energy output. With built-in web-based connectivity, operators can manage the system remotely, gaining insights and facilitating proactive maintenance.

In conclusion, the Siemens SINVERT 350 series combines robust performance, innovative technologies, and reliable safety features to create a compelling choice for large-scale solar energy projects. Its advanced design ensures operational efficiency and adaptability, thereby enhancing the overall viability of solar energy as a sustainable power source.
Top Page Image Contents