Soleus Air SG-WAC-12HCE operating instructions Masonry Construction, Support Bracket Wooden Strip

Page 13

ASSEMBLY & INSTALLATION - THRU-THE-WALL (CONT.)

Refer to the SUPPORT BRACKET ASSEMBLY in the WINDOW MOUNTING section to assemble the support brackets. A wooden strip nailed to the outside wall should be used in conjunction with the angled sill support brack- ets.

FIG. 3

Support

Bracket

Wooden Strip

5.Screw or nail the cabinet to the wooden frame using shims if the frame is oversized, to eliminate possible noise. Remember to maintain proper slope for water elimination.

FIG. 4

MASONRY CONSTRUCTION

1.Cut or build a wall opening in the masonry wall similar to the frame construction (refer to the THRU-THE- WALL installation for a wall thickness greater than 8 1/2”)..

2.Secure the cabinet in place using masonry nails, or masonry anchor screws. Or, build a frame using the instructions found in the THRU-THE-WALL installation section.

3.Make sure the masonry above the cabinet is supported well. Use the existing holes in the cabinet or additional drilled holes to fasten the cabinet at various positions.

Make sure that the side louvers are clear of any ob- structions.

4.Install the exterior cabinet support brackets according to the SUPPORT BRACKET INSTALLATION instruc- tions in the THRU-THE-WALL installation section.

Caulk or flash with aluminum if needed. This will pro- vide a tight seal around the top and sides of the cabi- net.

5.For a more aesthetically pleasing installation, apply wood trim molding around the sides of the cabinet with- out obstructing the side louvers.

6.Install the chassis into the cabinet by following the steps described in the WINDOW MOUNTING section.

OPTIONAL: Caulking and installation of the trim on the interior wall may be done if desired. Caulk the openings around the top and sides of the cabinet and all sides of the wood sleeve to the opening.

NOTE: See the WINDOW MOUNTING instructions for the bottom rail seal location.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents SG-WAC-12HCE Important Safety Instructions Electrical Requirements Lcdi Power Cord and PlugRecommended Ground Method Location Requirements Parts List Tools NeededModel SpecificationsPrior to Installing the Air Conditioner Installation & Assembly InstructionsWindow Preparation Storm Window RequirementsRemove Chassis Installation & Assembly Instructions Window MountingInstallation & Assembly Instructions Window Mounting Top Angle Rail and Side Bracket Installation Assembly & InstallationPlacing the Cabinet Inside the Window Foam Gasket and TopExtend the Accordion Panels Install the Window Lock and Sash SealInstalling the Chassis into the Cabinet THRU-THE-WALL InstallationSelect the Wall Location Prepare the WallPrepare and Install the Cabinet Assembly & Installation THRU-THE-WALLSupport Bracket Wooden Strip Masonry ConstructionElectronic Control Panel & Remote Control Using Your AIR ConditionerRemote Control Normal Operating SoundsUsing Your AIR Conditioner Using Your AIR Conditioner Air Filter Cleaning Care and CleaningCabinet Cleaning Winter StorageTroubleshooting Water is dripping inside the room Water is dripping outsideWater collects in the base pan One Year Limited Warranty Warranty
Related manuals
Manual 20 pages 12.18 Kb

SG-WAC-12HCE specifications

The Soleus Air SG-WAC-12HCE is a powerful and efficient window air conditioning unit designed to provide a comfortable indoor climate even during the hottest summer months. With its sleek design and effective cooling capabilities, this air conditioner has gained popularity among consumers looking for reliability and performance.

One of the standout features of the Soleus Air SG-WAC-12HCE is its 12,000 BTU cooling capacity, making it suitable for medium to large rooms up to 550 square feet. This powerful cooling performance is complemented by a dehumidification mode, which can remove up to 3.5 pints of moisture per hour. This combination ensures that not only is the air cooled down but also makes it less humid, providing a more comfortable living environment.

Energy efficiency is another primary characteristic of the SG-WAC-12HCE. With an Energy Efficiency Ratio (EER) of 12.0, this unit is designed to reduce energy consumption while delivering optimal cooling performance. This feature is essential for those looking to keep energy bills in check while maintaining a pleasant indoor atmosphere. The unit is also ENERGY STAR certified, demonstrating its commitment to minimal environmental impact.

The Soleus Air SG-WAC-12HCE comes equipped with an array of user-friendly controls. It features an intuitive remote control, allowing users to adjust the temperature settings, fan speeds, and modes from the comfort of their couch or bed. The electronic controls include a digital display, making it easier to monitor and set the desired cooling levels accurately.

Additionally, this air conditioner offers three cooling speeds and three fan-only speeds, giving users the flexibility to customize their comfort level based on personal preferences and varying weather conditions. The unit also features a programmable 24-hour timer, which allows for scheduled operation, ensuring the air conditioner only runs when needed.

Installation of the SG-WAC-12HCE is straightforward, thanks to the included window installation kit, which makes it compatible with most standard window sizes. Overall, the Soleus Air SG-WAC-12HCE is a feature-rich window air conditioning unit that excels in cooling efficiency, user convenience, and versatility, making it an exceptional choice for consumers looking to stay cool and comfortable.
Top Page Image Contents