HP BL30p Server Blades BL30p manual Rack Airflow

Page 20

QuickSpecs

HP ProLiant BL30p Server Blade

Standard Features (Manageability)

Minimum Rack Requirements

Mounts in ProLiant, and Telco racks and Third Party racks that meet the following criteria:

Compatible with 19-inch Standard EIA rail sets

EIA rail-to-rail depth is 29 - 30"

Cabinet depth must be at least 36-inch deep overall (Additional min. 3.5-inch clearance from rear RETMA rail to rear door, inclusive in the 36-inch overall depth)

Ample room for top and bottom cable egress (approximately 8 square inches for full rack configuration with patch panel)

Must be capable of supporting 1600 lb (for full rack configuration)

Perforated front and rear doors to accommodate front-to-back cooling

Must have 65% open perforation on server blade enclosure doors to support airflow requirements

Optimized for use with the HP 10000 Series racks

NOTE: If using Compaq 7000 Series rack, Rack Extension Kit and High Air Flow Rack Door options are required.

Rack Airflow

HP 10000 series racks provide enhanced airflow for maximum cooling, allowing racks to be fully

Requirements

loaded with servers and server blades using the latest server technologies.

CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment:

Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation).

Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 2.75 inches (7 cm).

CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.

NOTE: For additional information, refer to the Setup and Installation Guide or the Documentation CD provided with the server, or to the server documentation located in the Support section on the HP ProLiant BL30p server blade website: http://www.hp.com/servers/bl30p.

Service and Support Three-year limited warranty, including hardware diagnostic support, pre-failure warranty (coverage of processors, memory and SCSI hard drives). The warranty is fully supported by HP Services and a worldwide network of resellers and service providers. In addition 90-day's getting started software telephone support may be covered under the warranty or available for an additional fee. Enhancements to warranty services are available through HP Care Pack services.

NOTE: Server Blade Limited Warranty includes 3 year Parts, 1 year Labor, 1-year on-site support.

NOTE: Server Blade Enclosure and Interconnects Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site support.

Care Pack services provide a range of life cycle support options that let you choose the service levels that meet your business requirements, from basic to mission-critical.

A full range of HP Care Pack hardware and software services are available including:

Installation and start up Education courses

Extended onsite hardware coverage hours from same business day 13 hours, 5 day to 24 hours, 7 days call window with options including 4-hour response or 6-hour Call To Repair Comprehensive range of software technical support for Microsoft, Linux, ProLiant Essentials and VMWare-based IT solutions helping to deliver high level of application availability. Response times

 

 

 

 

 

DA - 11958 Worldwide — Version 19 — August 15, 2005

Page 20

Image 20
Contents Overview Maximum density HP ProLiant BL30p server bladeHP ProLiant BL30p Server Blade HP BladeSystem p-Class Power EnclosuresHP BladeSystem p-Class Enhanced Server Blade Enclosures QuickSpecs Or Cgesm Interconnect Switch Oror Mini bus barsQuickSpecs QuickSpecs Standard Features Server Blade Local I/O Cable No PCI slots, all features integratedFiber Channel on the HP ProLiant BL30p server blade Enclosure Standard Features Server Blade Enclosure and InterconnectsProLiant BL p-Class Interconnect Switch Option QuickSpecs Cgesm or GbE2 switches blades series ProLiant BL p-ClassSupports a pair of two ProLiant BL p-Class RJ-45 Patch PanelRequired Network 10Base-T Categories 3, 4 or 5 UTP 100 metersCabling EIA/TIA-568 100-ohm STP 100 metersStandard Features Power System and Rack Information QuickSpecs Standard Features Manageability Optional ProLiant Essentials Value PacksSmartStart OS SupportQuickSpecs Availability Features SecurityRack Airflow QuickSpecs Models ProLiant 3.06-GHz BL30p Processors 1GB 1PProLiant 3.2-GHz BL30p Model For 1GB Total Memory choose a or BFor 2GB Total Memory choose two For 4GB Total MemoryOptions Unique OptionsProLiant BL30p/BL35p AdapterQuickSpecs 380625-B22 Enhanced ServerManagement Suite Blade EnclosuresPower Options HP BladeSystem p-Class Interconnects283192-B21 Two QuadT2 Interconnect ModulesOther Options HP BladeSystem Power Extension Kit 381686-B21SAN Switches Sdlt 600 technology Ultrium 460 technologyHP StorageWorks MSL5026S2 Tape Library HP StorageWorks MSL5052S2 Tape LibraryHP StorageWorks EML E-Series Tape Libraries HP StorageWorks Virtual Library SystemsHP StorageWorks 9.1 GB Mid-range Optical Jukeboxes HP StorageWorks 9.1 GB High-end Optical JukeboxesHP StorageWorks Ultra Density Optical Storage HP StorageWorksModular Smart Array 1000Cluster Options ProLiant Cluster Starter kit 364023-B21USB Options HP Rack 5000 SeriesRack 10000 Series HP Rack 10842 42U Shock Pallet 257415-B22Service and Support Rack Options for HPHardware Services On-site Service Installation & Start-up ServicesSoftware Operating Environment Care Packs Memory HP ProLiant BL30p Server Blade all models Standard MemoryStandard Memory Replaced with Optional Memory Memory Slot Standard 1024 MB OptionalHP BladeSystem p-Class Dimensions Input SpecificationsTemperature Range Wet Bulb TemperatureTechnical Specifications Power RequirementsBL p-Class GbE Weight Interconnect Switch Forwarding Mode MAC AddressesSafety Forwarding TableAge Time Memory ComplianceBL p-Class GbE2 Weight Forwarding ModePower RequirementsInterconnect Switch Weight Requirements Temperature Range Operating Single-Phase Model Performance DimensionsWeights BladeSystemSpecifications Ambient TemperatureOutput Voltage Range See NotePower Bus Box Mini Bus Bar Scalable Bus Bar Supported enclosures DimensionsVoltage Max Total Power Max Current Per PowerSpecifications for Rate Max Rated PowerOperating Voltage CurrentQuickSpecs