HP 3C905B-TX manual HP Support Services, PC Cannot Be Started or Woken up from the Network

Page 19

NOTE

HP 10/100 3Com 3C905B-TX Network Interface Card Installation Guide

HP Support Services

The PC Cannot Be Started or Woken up from the Network

Check that the WOL connector cable is connected to the network interface card and to the PC’s system board.

If the PC has been powered off (for example, due to an electrical power failure, or because the power cord has been removed), the Remote Power On (RPO) will not work. To enable the RPO, you must first power on the PC, allow Windows 95 or NT 4.0 to boot, then shut down the PC.

Check that the WOL connector cable is connected to the network interface card and to the PC’s system board.

Check that the LAN-specific fields in the HP PC Setup utility are correctly set (refer to refer to “Updating LAN-specific Fields in the HP PC Setup Utility” on page 9).

RPO is only supported under Windows 95 and Windows NT 4.0.

HP Support Services

The latest drivers and utilities are available on HP’s Web site at:

http://www.hp.com/go/vectrasupport

English 15

Image 19
Contents Page Page Chapter Page Page English What’s in the Network Kit? Installation RequirementsNetwork Kit includes the following items Supported Platforms NT Service PackOperating System Master Diskettes Following network drivers are supported by Hewlett-Packard Supported Network DriversNon-Supported Network Drivers Overview of the Installation ProcedureInsert the card into the accessory slot without bending it Installing the Network Interface CardRemote Wake Up Connecting to the NetworkIf you want to wake up your PC from the network Updating LAN-specific Fields in the HP PC Setup UtilityIf you want to boot from the network If you want to power on your PC from the networkSoftware Installation on a Windows 95 System Software Installation ProcedureConfirming Installation Restart your PC Software Installation and Update on a Windows NT 4.0 SystemSelect OEM Option box, select 3Com EtherLink Adapter 3C905B Installing the DriverUpdating the Driver Checking the Installation3C905B-TX Card Does Not Work TroubleshootingPC Cannot Be Started or Woken up from the Network HP Support ServicesSpecifications 3C905B-TX NIC SpecificationsPhysical Layout LED LAN Connection Status LEDsRegulatory Information FCC for USA only Hardware WarrantyPage Page Hinweis Das Network Kit umfaßt die folgenden Komponenten InstallationsvoraussetzungenWas enthält das Network Kit? Unterstützte BetriebssystemeBetriebssystem-Masterdisketten Unterstützte PlattformenUnterstützte Netzwerktreiber Nicht unterstützte Netzwerktreiber Installieren der Network Interface Card Überblick über den InstallationsvorgangDeutsch Anschluß an das Netzwerk Aufrufen des HP PC Setup Programms Wenn Sie Ihren PC über das Netzwerk einschalten wollen Installation der SoftwareInstallation der Software auf einem Windows 95 System Wenn Sie Ihren PC über das Netzwerk aufwecken wollenKlicken Sie auf Entfernen. d Starten Sie Ihren PC neu Bestätigung der InstallationWählen Sie 3Com EtherLink Adapter 3C905Bim Fenster Installation des TreibersAktualisieren des Treibers Wählen Sie 3Com EtherLink XL NIC Überprüfen der InstallationDie 3C905B-TX Karte funktioniert nicht FehlersucheRPO ist nur unter Windows 95 und Windows NT 4.0 verfügbar HP KundenservicePhysikalisches Layout Spezifikationen der 3C905B-TX NICSpezifikationen LED LAN-Verbindung Status LEDsInformationen zur Konformität HP-Hardware-Garantie Page Page Français Le kit Réseau comprend Caractéristiques dinstallationQue contient le kit Réseau ? Systèmes dexploitation supportésPlateformes supportées Service Pack NTDisquettes originales du système dexploitation Pilotes de réseau supportés Pilotes de réseau non supportés Généralités sur la procédure dinstallationInsérez la carte dans lemplacement accessoire sans la tordre Installation de la carte dinterface réseauConnexion au réseau Sortir le système du mode veille à distanceAppuyez sur Redémarrez le PCInstallation du logiciel sous Windows Procédure dinstallation du logicielCliquez sur PCI Ethernet Controller ou sur lentrée Confirmation de linstallationCliquez sur Supprimer Redémarrez votre PC Installation du pilote Installation du logiciel et mise à jour sous Windows NTCliquez sur OK Mise à jour du pilote Vérification de linstallation La carte 3C905B-TX ne fonctionne pas Détection des défautsServices de support technique de HP Description physique Caractéristiques de la carte NIC 3C905B-TXCaractéristiques Voyants détat de la connexion LAN Declaration DE Conformite Informations réglementairesGarantie HP Page Aviso El Network Kit incluye los siguientes artículos ¿Qué hay en el Network Kit?Requerimientos de instalación Sistemas Operativos que admiten la instalaciónDisquetes Principales del Sistema Operativo Plataformas SoportadasDrivers de Red Soportados Drivers de Red no Soportados Resumen del Procedimiento de InstalaciónInstalación de la Tarjeta de Interfaz de Red Activador Remoto Conexión a la RedPulse Reinicie su PCSi desea arrancar por medio de la red Instalación del Software en un Sistema con Windows Procedimiento de Instalación del SoftwareHaga clic en Suprimir Arranque de nuevo su PC Confirmación de la InstalaciónAdaptador y haga clic en el botón Añadir Instalación del DriverHaga clic en OK Actualización del driver Haga clic en Actualizar Verificación de la InstalaciónAutomáticamente La Tarjeta 3C905B-TX No Funciona Resolución de ProblemasEl PC no se Puede Arrancar ni Activar por medio de la Red Servicios de Asistencia HPPresentación Especificaciones de la tarjeta 3C905B-TXEspecificaciones LEDs de estado da la conexión LAN Información Regulatoria Condiciones Válido sólo en México Póliza de GarantíaTeléfono Garantía del Hardware HP Page Avvertenza Il Network Kit comprende i seguenti elementi Requisiti per linstallazioneComponenti del Kit di rete Sistemi operativi supportatiDischetti originali del sistema operativo Piattaforme supportateHewlett-Packard supporta i seguenti piloti di rete Piloti di rete supportatiPiloti di rete non supportati Generalità sulla procedura di installazioneInstallazione della scheda di interfaccia di rete NIC Wake Up remoto Collegamento alla reteChip di ROM che include linizializzazione Dellutilità Setup del PC HPRiavviare il PC PremereInstallazione del software in un sistema dotato di Windows Procedura di installazione del softwareConferma dellinstallazione Fare un doppio clic sullicona Pannello di controllo Installazione del pilota Aggiornamento del pilota Verifica dellinstallazioneLa scheda 3C905B-TX non funziona Soluzione dei problemiNon si riesce a risvegliare o riaccendere il PC dalla rete Servizi di supporto HPArchitettura Specifiche 3C905B-TX NICSpecifiche LED di stato di connessione LAN Informazioni regolamentari Garanzia hardware HP Page Page Paper not bleached with chlorine Part number D6500-90001