HP c-Class Solaris manual Enabling the override parameter

Page 15

•Enabling full slot power draw—Some PCIe slots provide additional power (often up to 75 W of power). If your PCIe slot is rated to provide at least 55 W, then you can allow the device to draw full power from the PCIe slot by setting a VSL module parameter. For more information on enabling this override parameter, see "Enabling the override parameter (on page 15)."

CAUTION: If the PCIe slot is not capable of providing the needed amount of power, then enabling full power draw from the PCIe slot might result in malfunction or even damage to server hardware. The user is responsible for any damage to equipment due to improper use of the override parameter. HP expressly disclaims any liability for damage arising from improper use of the override parameter. To confirm the power limits and capabilities of each slot, as well as the entire system, contact the server manufacturer. For information about using the override parameter, contact HP Customer Support.

NOTE: The override parameter overrides the setting that prevents devices from drawing more than 25 W from the PCIe slot. The parameter is enabled by device using the device serial numbers. Once the setting is overridden, each device might draw up to the full 55 W needed for peak performance.

Before you enable the override parameter, ensure that each PCIe slot is rated to provide enough power for all slots, devices, and server accessories. To determine the power slot limits, consult the server documentation, BIOS interface, setup utility, or use the fio-pci-checkcommand.

Important considerations

•If you are installing more than one dual IO Accelerator device and enabling the override parameter for each device, be sure the motherboard is rated to provide 55W power to each slot used. For example, some motherboards safely provide up to 75W to any one slot, but run into power constraints when multiple slots are used to provide that much power. Installing multiple devices in this situation might result in server hardware damage. Consult with the manufacturer to determine the total PCIe slot power available.

•The override parameter persists in the system and enables full power draw on an enabled device even if the device is removed and then placed in a different slot within the same system. If the device is placed in a slot that is not rated to provide 55W of power, your server hardware could experience a power drag.

•The override parameter is a setting for the IO Accelerator VSL software by server and is not stored in the device. When moved to a new server, the device defaults to the 25 W power limit until an external power cable is added or the override parameter is enabled for that device in the new server. To determine the total PCIe slot power available for the new server, consult the manufacturer.

Enabling the override parameter

1.Use one of the following methods to determine the serial number of each device to be installed in a compatible slot:

oEnter the fio-status command: Sample output:

fio-status

...

Adapter: Dual Controller Adapter

Fusion-io ioDrive2 DUO 2.41TB, Product Number:F01-001-2T41-CS-0001, FIO SN:1149D0969

Maintenance 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HP IO Accelerator 3.2.3 Solaris User Guide Page Contents Upgrading devices About this guide Contents summaryIntroduction OverviewProduct naming IO Accelerator capacity 320GB 640GB Models AJ878B BK836A Performance attributesSupported firmware revisions Required operating environmentIntroduction Introduction Software installation Installation overviewInstalling the software and utilities Dev/rdsk/c*d0p0 Loading the IO Accelerator VSL facility driverUpgrading the firmware $ pfexec remdrv iomemory-vslEnabling PCIe power Using the device as a swapConfiguring a ZFS pool Enabling PCIe power override MaintenanceMaintenance tools Command-line utilitiesEnabling the override parameter Disabling auto attach Uninstalling IO Accelerator VSL and utilitiesUnmanaged shutdown issues Options iomemory-vsl externalpoweroverride=valueDisabling the IO Accelerator VSL Enabling the IO Accelerator VSL$ pfexec remdrv iomemo Monitoring and managing devices Introduction to monitoring and managing devicesManagement tools Example conditions to monitor Device LED indicators Limiting Apci C-states Performance and tuningIntroduction to performance and tuning Disabling DvfsFio-attach device options UtilitiesUtilities reference Fio-attachTmp/fio-bugreport-20100121.173256-sdv9ko.tar.bz2 Fio-beaconFio-bugreport Fio-beacon device optionsFio-detach Fio-format Fio-detach device optionsFio-format options device Fio-status device options Fio-statusFfield Fio-sure-erase Fio-sure-erase options device Fio-update-iodrive Fio-update-iodrive options iodriveversion.fff Domainbusslot.func Monitoring IO Accelerator health Nand flash and component failureHealth metrics Health monitoring techniques Using module parameters ZFS pools and health monitoringEsxcfg-module --server server-name iomemory-vsl -g Upgrade procedure Upgrading devicesUpgrading devices for IO Accelerator VSL 2.x.x to $ modprobe iomemory-vsl Upgrading devices Subscription service ResourcesFor more information Customer Self Repair Support and other resourcesBefore you contact HP HP contact informationRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Acronyms and abbreviations Documentation feedback Index Index
Top Page Image Contents