SETTING UP THE SURROUND SOUND SYSTEM
Your Home Theater Audio System speakers are timbre matched and ready to use “as is” as soon as you unpack them. If you wish to
Important Notes:
•To change the surround sound settings, the receiver must be in a surround mode that uses all the speakers (for example, Dolby Digital).
•The center and surround speakers only operate when the receiver is set to a surround sound mode and the source material being played is recorded or broadcast in Dolby Digital, DTS or Dolby Pro Logic surround sound.
•Stereo broadcasts or recordings will produce some surround channel effects when played in a surround mode. However, mono sources will not produce any sound from the surround speakers.
Changing the Speaker Distance
When you have arranged your home theater (speakers, receiver, and any components), you can change the speaker distance entered in the receiver’s memory. The default setting is 20 feet.
1.Imagine a straight line from the front left speaker to the front right speaker.
2.Measure the distance in a perpendicular line from your listening position (for example, your couch) to the imaginary line. (See illustration on page 6.)
Note: Do not measure the distance to the speakers, just the line.
3.Repeat Steps
4.Measure the distance in a perpendicular line from your listening position (for example, your couch) to the center speaker.
5.3Press SETUP, then press 8 twice. IFý:?IJ appears.
6.Press 7. <HEDJ appears.
7.Press 7again. <ý(&<J appears. To change the distance
between the listening position and the front speakers, repeatedly press 8 or 9 until you reach the desired distance ('ýto )&ý<J).
8.Press ENTER. 9;DJ;H appears.
9.Press 7. 9ý(&<J appears. To change the distance between
the listening position and the center speaker, repeatedly press 8 or 9 until you reach the desired distance ('ýto )&ý<J).
10.Press ENTER. IKHH$ appears.
11.Press 7. Iý(&<J appears. To change the distance between
the listening position and the surround speakers, repeatedly press 8or 9until you reach the desired level ('ýto )&ý<J).
12.Press ENTER. <HEDJ appears.
13.Press SETUP to exit.
Changing the Channel Level
The default channel level settings are 0 dB for each speaker. You can change the speakers’ sound distribution to suit your surround sound needs. For example, if you are closer to the left front speaker than the right front speaker, the left front speaker might seem “louder” than the right one. To adjust it, you must change the channel level for one or both speakers until the sound evens out.
1.3Press SETUP, then 8. 9>ýB;L;B appears.
2.Press 7. <BýB;L;Býappears.
3.Press 7 again. <Bý&Z8 appears. To change the front left speaker’s level, repeatedly press 8 or 9 until you reach the desired level (¶'& to !'&ýZ8).
4.Press ENTER. 9ýB;L;B appears.
5.Press 7. 9ý&Z8ýappears. To change the center speaker’s level, repeatedly press 8 or 9 until you reach the desired level (¶'& to !'&ýZ8).
6.Press ENTER. <HýB;L;B appears.
7.Press 7. <Hý&Z8ýappears. To change the front right speaker’s level, repeatedly press 8 or 9 until you reach the desired level (¶'& to !'&ýZ8).
8.Press ENTER. IHýB;L;B appears.
9.Press 7. IHý&Z8ýappears. To change the right surround speaker’s level, repeatedly press 8 or 9 until you reach the desired level (¶'& to !'&ýZ8).
10.Press ENTER. IBýB;L;B appears.
11.Press 7. IBý&Z8ýappears. To change the left surround speaker’s level, repeatedly press 8 or 9 until you reach the desired level (¶'& to !'&ýZ8).
12.Press ENTER. IMýB;L;B appears.
13.Press 7. IMý&Z8ýappears. To change the sub woofer’s level, repeatedly press 8or 9until you reach the desired level (¶'& to !'&ýZ8).
14.Press ENTER. <BýB;L;B appears.
15.Press SETUP to exit.
Changing the Speaker Size
Note: If you are using the speakers provided in your Home Theater Audio System, the speaker size defaults are correct. If you are using other speakers, follow these steps.
1. 3Press POWER.
3— Use the remote for these steps. 4— Use the receiver for these steps. 3or 4— Use either device for these steps. | 13 |
|