S.M.A.R.T. Command, Register, Code in Features

HP 8566c (US), 6671 (LA), 6642D (US), 6641 (LA) manual S.M.A.R.T. Command, Register, Code in Features

Page 38

U8 Family Product Manual, Rev. B		31

Code in Features	S.M.A.R.T. Command
Register


D6H	S.M.A.R.T. Write Log Sector
D7H	Obsolete

D8H	S.M.A.R.T. Enable Operations

D9H	S.M.A.R.T. Disable Operations

DAH	S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

Image 38

Contents

ST38410A, ST34313A U8 FamilyST317221A, ST313021A Ultra ATA Interface DrivesST38410A, ST34313A U8 FamilyST317221A, ST313021A Ultra ATA Interface DrivesPage Contents U8 Family Product Manual, Rev. BConfiguring and mounting the drive ATA interfaceFigures U8 Family Product Manual, Rev. B Introduction ST317221A Specification summary tableDrive Specification ST313021AST317221A 0 to 60C op., -40 to 70C nonopST313021A 1.1 Formatted capacity 1.0 Drive specifications1.1.1 Default logical geometry 1.2 Physical organization1.3 Recording and interface technology 1.4 Physical characteristicsDrive Specification 1.5 Seek timeSpinup power 1.7 Power specifications1.7.1 Power consumption 1.6 Start/stop timesIdle mode power Read/Write power and currentOperating power and current Seek ModeTypical Watts Power Mode1.7.1.1 Typical current profile Typical Amps RMS1.7.2 Conducted noise 1.7.4 Power-management modesPower Modes 1.7.3 Voltage tolerance1.8.2 Temperature gradient Idle and Standby timers1.8 Environmental tolerances 1.8.1 Ambient temperature Sleep mode1.8.3 Humidity 1.9 Drive acoustics 1.8.6.1 Operating vibration1.8.6.2 Nonoperating vibration 1.11 Reliability 1.12 Agency certification 1.12.1 Safety certification1.10 Electromagnetic susceptibility 1.12.2 Electromagnetic compatibility1.12.3 FCC verification Australian CE-Tick N176U8 Family Product Manual, Rev. B 2.0 Configuring and mounting the drive 2.1 Handling and static-discharge precautionsOptions jumper block J8 Master or single drive Drive is slave 2.2 Jumper settings 2.2.1 Master/slave configuration7 5 3 8 6 4 Cable select2.3 Drive mounting 2.2.2 Cable-select option2.2.3 Ultra ATA/66 cable Figure 3. Mounting dimensions-top, side and end view Note Dimensions are shown in inches mm3.0 ATA interface 3.1 ATA interface signals and connector pinsHost pin # and signal description Figure 4. I/O pins and supported ATA signalsSignal name Drive pin #Command code in hex 3.1.1 Supported ATA commandsCommand name ATA-standard commands3.1.2 Identify Drive command Command code in hexx.xx WordDescription ValuexxxxH xx07Hxx1FH Bit Word xxA5HDescription if bit is set to Bit Word 3.1.3 Set Features command Set transfer mode based on value in Sector Count registerS.M.A.R.T. Command 3.1.4 S.M.A.R.T. commandsCode in Features RegisterCode in Features Page Page Publication Number SG35226-001, Rev. B, Printed in USA Seagate Technology, Inc920 Disc Drive, Scotts Valley, California 95066, USA

Related manuals

HP 8566c (US), 6671 (LA), 6642D (US), 6641 (LA) manual S.M.A.R.T. Command, Register, Code in Features

Code in Features