Roberts Gorden 225, 200 Servicing 12.1 Servicing Instructions, Burner Maintenance, Combustion Fan

Page 30

COMBAT® UHA UNIT HEATER INSTALLATION OPERATION AND SERVICE MANUAL

SECTION 12: SERVICING 12.1 Servicing Instructions

After start-up, the heater will require maintenance to be carried out annually. If the heater is used in a dirty or dusty area, more frequent maintenance may be necessary.

WARNING

Cut Hazard

Turn off gas and electrical supply before maintenance. Fan can start automatically at any time.

Failure to follow these instructions can result in severe injury or product damage.

NOTE 1: After any maintenance or repair work, always test fire the heater in accordance with the start-up instructions on Page 19, Section 10 through Page 21, Section 10.3.1 to ensure all safety systems are in working order before leaving the heater to operate. Minor faults may be traced by using the troubleshooting charts on Page 27, Section 13 through Page 30, Section 13.5.

NOTE 2: Check all gas pipes and pipe joints to ensure there are no cracks or gas leaks. Any cracks in the pipes or pipe joints must be repaired.

NOTE 3: Inspect all suspended components and hardware. Ensure that they are in good condition, properly tightened, and corrosion free.

12.2 Burner Maintenance

1.Open the door and remove the burner compart- ment cover. See Page 32, Section 14.2.

2.Clean any deposits from the main burner which may have formed in the injectors or venturi of the burner. See Page 32, Section 14.2.

3.Remove the ignition electrode and flame probe. Check condition of ignition electrode and flame probe. Clean off any deposits which may have been formed, check condition of ceramic insulators. Replace as necessary.

12.3 Fan/Motor Assembly Maintenance

The main fan bearings are permanently sealed and do not need lubrication. Before cleaning, turn off gas and electrical supply. Remove the fan and use a small brush or duster to clean the fan blades from each side. Replace fan when done.

12.4 Heat Exchanger Maintenance

The heat exchanger will remain clean unless a problem has developed with combustion. Inspect the heat exchanger. Look for signs of overheating at the front tubes which may indicate burner over firing or persistently low air flows.

12.5 Gas Valve Maintenance

No regular maintenance is required on this device. To change gas control valves, See Page 31, Step 14.1 and Page 35, Section 14.5.

Do not repair or disassemble gas valve. Replace faulty gas valves with genuine ROBERTS GORDON® replacement parts.

12.6 Combustion Fan

The combustion fan should not require maintenance. However, if the air pressure switch is causing burner lockout, then remove the combustion fan from the vent box by unscrewing the three screws at the mounting plate. Remove the four screws attaching the mounting plate to the fan inlet (See Page 34, Section 14.4). Ensure that the fan is free to run and that the fan wheel is clean.

12.7 Venting and Air Intake Pipe

Inspect all venting and air intake pipe. Ensure that all seams are sealed and suspension points secure. Repair suspension points if any part of the venting or combustion air pipe is sagging. Check to make sure any insulation is not missing or in poor condition. Replace as necessary. Check all venting and air intake components to ensure they are in good condition, gas tight and corrosion-free.

24

Image 30
Contents Combat Page Roberts-Gordon, LLC Page Table of Figures Page Heater Safety Manpower RequirementsCorrosive Chemicals Installer ResponsibilityWall Tag National Standards and Applicable CodesCritical Considerations 3.1 Basic Information Minimum Required Installation ClearancesSeparated Combustion Installation Clearances to CombustiblesInstallation Clearances and Clearances to Combustibles National Standards and Applicable Codes Major Components 5.1 General SuspensionUnited States Requirements Vent InstallationVenting 6.1 Venting Canadian RequirementsHorizontal Venting Separated Combustion Heaters Models Uhas 150Unvented Operation Vertical VentingVent Material Vent and Roof DetailStandard Vented Heater Common Vertical Vent Termination Concentric Vent Box Horizontal Building Ventilation Unvented InstallationAIR Supply Outside Combustion Air SupplyGAS Piping ConnectionsFan Control WiringPositioning Thermostats Low Voltage Thermostat with One HeaterUhas Series Internal Wiring Diagram TransformerUhas Series Ladder Wiring Diagram Electrical Connection to the Heater Electrical Checks Operation and MaintenanceLouvers Mechanical ChecksAutomatic Burner Control Sequence Turning Off the Heater Pressure SwitchCheck Gas Rate Complete the Start-UpHeater Operation Simple TroubleshootingSimple Troubleshooting Burner Faults To Turn the Heater OffUser Instructions Heat Exchanger Maintenance Burner Maintenance12.3 Fan/Motor Assembly Maintenance Gas Valve MaintenanceVicinity of the Heater Maintenance ChecklistInstallation Code and Annual Inspections All Vehicles and OtherWindow When installedBurner Observation Combustion Fan ScrollTroubleshooting 13.1 General Troubleshooting For Automatic Ignition Burner Systems Result in death or electrical shockTroubleshooting for Flame Supervision System StartTroubleshooting for Gas Valves Troubleshooting for Combustion FanConduct start-up procedure as shown on Page 19, Section Replacement Parts Burner ComponentsBurner Compartment Burner InjectorsIgnition Electrode and Flame Probe Description Part Number QtyCombustion Fan Vertical Installation Uhas Fan Removal and Replacement Axial Fan/Guard/Motor AssemblyLimit Switches Removal and Replacement To Replace the Fan AssemblySpecifications Standard Models 150 400 Uhas Series Dimension DataGeneral Technical Data Table All Models Technical Data Table All ModelsROBERTS-GORDON will not PAY for Warranty is Void ifROBERTS-GORDON will PAY for Limitations on Authority RepresentativesPage Page Some objects can catch fire or explode when placed
Related manuals
Manual 52 pages 19.42 Kb Manual 62 pages 5.65 Kb

175, 225, 300, 250, 400 specifications

Roberts Gorden is a recognized leader in the field of heating solutions, particularly renowned for the development of its innovative radiant heating systems. The lineup of models including the Roberts Gorden 250, 300, 400, 150, and 225 features a blend of advanced technology, exceptional efficiency, and versatile applications that cater to various industrial and commercial needs.

At the core of Roberts Gorden products is their radiant heating technology. Unlike conventional heating systems that warm the air, radiant heaters emit infrared radiation, which directly heats objects and people within a space. This method not only provides a comfortable environment but also reduces energy consumption and minimizes the loss of heat, making it an environmentally friendly choice.

The Roberts Gorden 250 model is specifically designed for smaller spaces, offering compact efficiency without sacrificing power. It features an adjustable output, allowing for tailored heating based on specific requirements. The advanced burner technology ensures optimum combustion efficiency, translating to cost savings on fuel consumption.

Moving on to the Roberts Gorden 300, this unit is well-suited for medium-sized facilities. With enhanced capabilities, the 300 model offers improved heating distribution, making it ideal for warehouses and production floors. The ease of installation and maintenance further enhances its appeal, allowing businesses to focus on their operations rather than on complicated heating systems.

The Roberts Gorden 400 is a powerhouse in the lineup, engineered for larger spaces that demand high-performance heating. Its robust construction and powerful output provide effective warmth even in challenging environments. The unit is equipped with sophisticated controls that promote energy efficiency while maintaining optimum comfort levels.

In the mid-range spectrum, the Roberts Gorden 150 and 225 models cater to businesses needing versatile heating solutions. Both models are designed with user-friendly interfaces and include safety features that comply with industry standards. Their lightweight design allows for easy installation and mobility, making them suitable for temporary or permanent heating applications.

Overall, Roberts Gorden's commitment to innovation and efficiency is evident across its product range. With a focus on sustainability and advanced heating technologies, the Roberts Gorden 250, 300, 400, 150, and 225 models provide reliable heating solutions that meet the diverse preferences of industrial and commercial users. These products are not just about warmth; they are about creating a comfortable and productive environment while minimizing energy costs and environmental impact.