York YCJD18 THRU 60 warranty Sound Power Ratings

Page 16

840569-YTG-A-0612

ACCESSORIES

Refer to Price Manual for specific model numbers.

Off Cycle Timer Delay - Provides a 5-minute off cycle to pre- vent rapid recycling of the compressor.

Start Assist Kit (S1-2SA067*) - Provides increased starting torque for areas with low voltage. See Hard Start Kit Accessory Installation Manual for Hard Start Kit part number for each model.

TXV Kits - S1-1TVM series thermal expansion valves precisely meter refrigerant for optimum performance over a wide range of conditions. See System Charge table for TXV part number for each model.

Thermostats - Compatible thermostat controls are available through accessory sourcing. For optimum performance and installation, refer to the UPGNET “Low Voltage Wiring Diagram” document to select and apply controls.

SOUND POWER RATINGS

UNIT MODEL

(dBA)

18

69

24

72

30

71

36

71

42

75

48

74

60

74

Rated in accordance with ARI Standard 270-1995.

TYPICAL INSTALLATION

60” OVERHEAD CLEARANCE

10” CLEARANCE AROUND PERIMETER

NOTES:

ALL OUTDOOR WIRING MUST BE WEATHERPROOF. MINIMUM 24” UNIT TO UNIT CLEARANCE.

MINIMUM 18” SERVICE ACCESS CLEARANCE ON ONE SIDE

WEATHERPROOF

DISCONNECT

SWITCH

CONTROL

ACCESS

PANEL

THERMOSTAT

NEC CLASS 1 WIRING

NEC CLASS 2 WIRING

TO FURNACE OR

AIR HANDLER

TERMINAL BLOCK

TO INDOOR COIL

SEAL OPENING(S) WITH PERMAGUM OR EQUIVALENT

TYPICAL FIELD WIRING

ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES

POWER WIRING

208/230-1-6024 VOLT CONTROL WIRING MINIMUM 18 GA. WIRE

(NEC CLASS 2)

POWER WIRING CONTROL WIRING FACTORY WIRING

CONTACTOR

TERMINALS

GND.

LUGCOIL

CONDENSING UNIT

FURNACE OR AIR HANDLER TERMINAL BLOCK

C Y R G W

* TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT.

*

Y R G W

ROOM THERMOSTAT

ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.

16

Johnson Controls Unitary Products

Image 16
Contents Technical Guide Physical and Electrical Data ModelSystem Charge for Various Matched Systems Procedures FootnotesUnit AIR Handler Cooling Model Width MODEL1 Rated NET MBH Seer EER CFMSens Seer AC with AIR HandlersMV12D 24.5 1600 Coil CFM Range Cooling Unit Model Rated NET MBH Seer Width Seer AC Coil only RatingsCooling Capacity With High Efficiency Motor Furnaces FC/MC/PC43C FC/MC/PC48C FC/MC/PC60D UC60D 1410 42.0 30.0 13.50 11.50 9C*C16 21.0 9C*C20 21.0 Sound Power Ratings Temperature AIR Conditioner Model noIndoor Coil Model no FC/MC/PC18 Condensing Idcfm Entering AIRIndoor Coil Model no FC/MC/PC36 Condensing FC/MC/PC32A Indoor Coil Model no FC/MC/PC32 Condensing FC/MC/PC43C Indoor Coil Model no FC/MC/PC37 Condensing FC/MC/PC48C Indoor Coil Model no FC/MC/PC43 Condensing UC60D Indoor Coil Model no FC/MC/PC48 Condensing Indoor Coil Model no FC/MC/PC60 Condensing Idcfm York International Corp York Drive Norman, OK
Related manuals
Manual 18 pages 57.82 Kb

YCJD18 THRU 60 specifications

The York YCJD18 THRU 60 is a dynamic heating, ventilation, and air conditioning (HVAC) system that incorporates advanced technology and design principles to deliver efficient climate control in commercial spaces. As part of York's heritage in the HVAC industry, this unit is engineered to meet diverse cooling and heating demands while maintaining high energy efficiency standards.

One of the main features of the YCJD series is its capacity range, which extends from 18 to 60 tons. This versatility makes it suitable for a variety of commercial applications, including office buildings, retail spaces, and educational institutions. The system utilizes a scroll compressor, known for its durability and quiet operation, ensuring that occupants experience minimal noise disruption during operation.

In terms of energy efficiency, the YCJD18 THRU 60 boasts high Seasonal Energy Efficiency Ratio (SEER) and Energy Efficiency Ratio (EER) ratings. These ratings indicate that the unit is well-equipped to handle cooling loads while consuming less energy compared to traditional HVAC systems. This not only translates to lower operational costs but also aligns with global initiatives towards sustainability and reducing carbon footprints.

The YCJD series incorporates advanced controls and monitoring technologies, allowing for precise adjustments and diagnostics. The integration of smart controls enables users to optimize system performance, schedule operations, and monitor energy usage from a remote interface. This feature enhances user experience while providing valuable insights into system efficiency and maintenance needs.

Another notable characteristic of the YCJD is its robust construction designed to withstand the rigors of various climates. The unit is typically equipped with high-quality insulation, weatherproof housing, and corrosion-resistant components, contributing to its longevity and reliability in different environments.

The installation flexibility is another strong point for the YCJD series, as it offers options for rooftop or ground-level placement. This adaptability makes it easy for HVAC professionals to customize installations to fit existing structures or new builds.

In summary, the York YCJD18 THRU 60 is a comprehensive HVAC solution designed for commercial use, featuring high energy efficiency, advanced control technologies, and robust construction. Its wide capacity range and installation versatility make it a reliable choice for maintaining comfortable indoor environments across diverse applications. With York's commitment to innovation, the YCJD series represents a significant step forward in HVAC technology, ensuring users benefit from enhanced performance and sustainability.