HP QR516B manual Additional New Primitives Support on ESXi, Vaai and New Feature Support Table

Page 55

Figure 11 Virtual Machine Message — Retry and Cancel options

Additional New Primitives Support on ESXi 5.x

HP 3PAR OS 3.1.1 or later supports additional new primitives, called TP LUN Reporting, where the ESXi 5.x is notified that a given LUN is a thin provisioning LUN by enabling the TPE bits of the READ Capacity (16) and enables the host to use features such as sending the UNMAP command to these LUNs. The TPE bit is enabled for TPVVs and R/W snapshot of TPVV base.

The Quota Exceeded Behavior present in ESXi 5.x is accomplished through the "Thin Provisioning Soft Threshold Reached" check condition, providing alerts and warnings.

VAAI and New Feature Support Table

The following table summarizes the VAAI plugin requirements and New Primitives support.

Table 3 HP 3PAR VAAI Plugin Installation Requirements

VMware ESX Features/Primitives

ATS

XCOPY

WRITE_SAME UNMAP

ESX 4.1

ESX 4.1

ESXi 5.x

HP 3PAR OS 2.3.1

HP 3PAR OS 3.1.1 or

HP 3PAR OS 2.3.1

MU2 or later

later

MU2 or later

Needs HP 3PAR VAAI

Needs HP 3PAR VAAI

Needs HP 3PAR VAAI

1.1.1 plugin

1.1.1 plugin

2.2.0 plugin

Not supported by ESX

Not supported by ESX

Not supported by

4.1 or later

4.1 or later

HP 3PAR OS 2.3.1

Not supported by

 

 

HP 3PAR OS 2.3.1

 

 

ESXi 5.x

HP 3PAR OS 3.1.1 or later

Supported. Does not require HP 3PAR VAAI plugin (supported by

Out-of-space

Supported. HP 3PAR

Supported. HP 3PAR

Supported. HP 3PAR

condition (aka

VAAI 1.1 plugin

VAAI 1.1 plugin

VAAI 1.1 plugin

“VM STUN”)

recommended, but not

recommended, but not

recommended, but not

 

required for this

required for this specific

required for this

 

specific feature.

feature.

specific feature.

Standard T10 ESX plugin).

Quota Exceeded

Not supported by ESX

 

 

Behavior

4.1 or later

Not supported by ESX

Not supported by

 

 

TP LUN Reporting

Not supported by

4.1 or later

HP 3PAR OS 2.3.1

HP 3PAR OS 2.3.1

 

 

 

 

 

ESX/ESXi 4.1, ESXi 5.x Additional Feature Considerations 55

Image 55
Contents HP 3PAR VMware ESX Implementation Guide Acknowledgments Contents Support and Other Resources Configuring the Host for an iSCSI ConnectionAllocating Storage for Access by the ESX Host TargetDocumentation feedback Required Supported ConfigurationsIntroduction RequiredAudience HP 3PAR OS Upgrade ConsiderationsSetting Up the Ports Configuring the HP 3PAR StoreServ Storage for Fibre Channel# showport -par # showhost -listpersona Creating the Host Definition# showhost -persona # showhost# controlport persona 7 nodeslotport # createhost ESXserver1 10000000C9724AB2 10000000C97244FE Setting Up and Zoning the FabricHP 3PAR Coexistence Configuration Guidelines for Fabric VendorsAdminportcfgfillword Target Port Limits and SpecificationsHP 3PAR Priority Optimization Persistent Ports # showport Persistent Ports Setup and Connectivity GuidelinesPersistent Ports Limitations Unsupported ConfigurationsSoftware iSCSI Support Configuring the HP 3PAR StoreServ Storage for iSCSISetting Up the Ports for an iSCSI Connection # controlport config iscsi # showport# vmkping # showport -iscsi# controliscsiport ping 10.1.1.10 ESX1 Setting Up and Configuring Chap Authentication Chap Authentication in ESX Chap Credentials in ESX/ESXi 4.x or ESX/ESXi For ESX 4.x # showhost -chap Hardware iSCSI SupportSetting a Static IP Address Showiscsisession Chap Configuration for One-Way Chap Chap Configuration for Mutual Chap HP 3PAR Priority Optimization Target Port Limits and Specifications# showport -fcoe Configuring the HP 3PAR StoreServ Storage for FCoE# controlport config fcoe # showport 031 # showport -i 031# controlport offline Showport Turn off the iSCSI portsCreating the Host Definition Target Port Limits and Specifications # esxcli brocade bcu --command=vhba --query 1/0 Configuring the Host for a Fibre Channel ConnectionInstalling the HBA and Drivers # esxcli brocade bcu --command=port --listHttp//kb.vmware.com Installing Virtual Machine Guest Operating System# cat /etc/rc.local Multipath Failover Considerations and I/O Load BalancingConfiguring the Host for a Fibre Channel Connection Multipath Failover Considerations and I/O Load Balancing LUN Set to Round Robin Vmwpsprr Vmwpspfixed Vmwpspmru To remove the above Alua custom Satp rule ESX/ESXi 4.0 GA 4.0 UxESXi ESX/ESXi 4.1 GA 4.1 UxDefault Satp Rules and Their Current Default PSP Satp Info Commands# esxcli storage nmp device list naa.50002ac0000a0124 Satp Custom Rules and Associated Defined ParametersShow Device Information # esxcli nmp satp listrules grep -i 3par# esxcli storage nmp device list -d naa.50002ac0005800ac # esxcli nmp device list naa.50002ac000b40125VMware ESX Releases through ESX 3.5 Update Performance Considerations for Multiple Host Configurations# esxcli nmp device list -d naa.50002ac0005800ac Esxcli storage core device list --device devicename VMware ESX Release 3.5 Update 4 through ESX 4.x and ESXiVMware ESXi Release # esxcli storage core device list497 / 16 = 31.xxx recommended max target port queue depth = Lpfcdd7xx Lpfcdd732 Lpfc740 Storage I/O Control ESX/ESXi 4.1, ESXi 5.x Additional Feature ConsiderationsVStorage APIs for Array Integration Vaai HP 3PAR Vaai Plugin 2.2.0 for ESXi HP 3PAR Vaai Plugin 1.1.1 for ESXi# mount -t ext4 -o discard /dev/sda2 /mnt # cd /vmfs/volumes/volune-nameUnmap Space Reclaim Storage Hardware Support for ESXi Out-of-Space Condition for ESX 4.1 and ESXi# showalert Additional New Primitives Support on ESXi Vaai and New Feature Support TableVaai Status supported Vaai Plugin Verification# esxcli storage core plugin list # esxcfg-scsidevs -l naa.50002ac0002200d7# esxcli storage core plugin list Plugin name Plugin class # esxcfg-scsidevs -l naa.50002ac003da00ebHardware Acceleration for HP 3PAR devices VMware All Paths DownUsing system Bios to configure FCoE Configuring the FCoE SwitchConfiguring FCoE Configuring the PCI Slots Exiting the Bios Utility Configuring Initiator FCoE to FC TargetInitiator FCoE to FC Target Configuring Initiator FCoE to Target FCoEInitiator FCoE to Target FCoE Installing iSCSI on VMware ESX Configuring the Host for an iSCSI ConnectionConfiguring the Host for an iSCSI Connection Creating a VMkernel Port Configuring the Host for an iSCSI Connection Click OK to complete Click Next Configuring the Host for an iSCSI Connection Page Configuring the VMware iSCSI Initiator Configuring the VMware iSCSI Initiator Configuring the Host for an iSCSI Connection Configuring the VMware iSCSI Initiator # showhost ESX/ESXi Additional Feature Considerations Using the HP 3PAR OS CLI Allocating Storage for Access by the ESX HostCreating Virtual Volumes for HP 3PAR OS 2.2.4 and Later Using the HP 3PAR Management Console# createaldvv -cnt 5 TESTLUNs 5G Creating Virtual Volumes for HP 3PAR OS 2.2.3 or EarlierExporting LUNs to an ESX Host # createaldvv options vvname.index sizegGtT# createvlun options VVname VVset LUN nodeslotport/hostname Creating a Vlun for Export# createvlun options VVname VVset LUN nodeslotport # createvlun options VVname VVset LUN hostname/setDiscovering LUNs on VMware ESX Hosts Removing VolumesEventlog and Host Log Messages Host and Storage UsageHost and Storage Usage Page Contacting HP Support and Other ResourcesHP 3PAR documentation Reference Storage Physical Planning HP 3PAR branding information Typographic conventionsDocumentation feedback