HP Connection Point 2W manual ISP service is

Page 82

Symptom

Possible Cause Solution

Cannot access access Internet (external web pages) on my PC through the Connection Point CP-2W (but can access the configuration pages).

Modem is not on.	Turn on DSL or cable modem.

No valid IP	Go to Connection Point CP-2W
address on	configuration pages. Click Renew
Connection Point	Internet IP under the Current Internet
CP-2W.	Status section of the Basic Setup tab.

ISP service is	Verify that DSL or cable modem is on and
down.	working properly by checking the
	modem’s LEDs. Consult modem
	documentation or ISP for information
	regarding modem status.

Previous MAC	Reset the cable or DSL modem: unplug
address was not	power to modem for anywhere from
released by cable	several minutes to several hours. Contact
or DSL modem.	ISP for more information.

Connection Point	ISP may require additional configuration
CP-2W Internet	information: PPPoE account user name
settings not	and password, DNS, device name, or
properly	MAC address. Contact ISP for specific
configured.	requirements and add them to your
	configuration.

ISP requires MAC	Found on System Information tab of
address of device	internal web page in the Internet Status
connected to	section in field labeled MAC Address.
Internet.

78	IPAQ CONNECTION POINT CP-2W

Image 82

Contents Page Copyrights, Trademarks, and Disclaimer Contents ++0&+ Introduction Features and Benefits802.11b Wireless Networking Share a Single High-Speed Internet ConnectionEthernet Networking Security and Advanced ManagementWhats in the Box? What Else Do I Need?04+ Whats in Front? Description SignificanceWhats in Back? Description FunctionInstallation and Configuration InstallationConnecting to Your PC Powering Up Client PC Configuration $B$,$Configuring Windows 98 and ME Clients 22!$B$$++ $!++ Internet Connection Logging++5,,,&$ Dynamic Internet IP Configuring Static Internet IP Static Internet IPPPPoE Ssid Installing the Firmware Update Utility Registering the Connection Point CP-2WAdding PCs to Your Network Wireless PCsEthernet PCs Windows 2000 Configuration 20!&+ 20!$++ $62!$B$7$++ 20!$++ 20!&+ Windows NT4.0 Configuration 22!$B$$++ # .,$!+ Wired Equivalent Privacy WEP Network SecurityAccessing Security Configuration Options Media Access Control MAC $!+ Enable MAC Filtering Add a MAC Filter Modify a MAC Filter Delete a MAC Filter System Information General InformationLAN Status Internet StatusWireless Statistics Network Information Event Log Advanced Configuration System SettingsResetting to Factory Default LAN Configuration Changing the Subnet Internet Configuration Dynamic IPStatic IP Changing Static IP Settings $$$$ Changing PPPoE Settings DMZ Virtual ServerAdding a Virtual Server Packet Filtering Enabling or Disabling Packet Filtering Adding an IP Rule 20$.++ Adding Port Rules +,++ Dhcp Reserved IP Table Adding a Reserved IP Address$2++ 20.5$++ Excluded IP Addresses @ 2$2++ 20$0++ ?,,++ $!$/ ++ Bootp IP Table Adding a Bootp IP Address2EE2$$2++ 20EE2$$++ Static Routing Table 20&.2++ +?+ +$,5 ?,$ 002+ +?0 $!$/ ++ 05&+ Access Point and Internet Router Configuration Configuring as an Access Point20$&+$+ Changing From Access Point Back to Internet Router $!$ ?,+ $!,!$!$ $!$/ ++ # ! 1!$!$ 05&+ +!$!$ ? +++$,,+,6+ ?-8M+ %%%27? $!$/ 1$ ++ ++5 System Update and Recovery 205&+++ Using the Firmware Update Utility +,5,4 Restore Factory Defaults Troubleshooting SolutionNetwork cables ISP service is Cannot see Regulatory Compliance Federal Communications Commission Notice25+$!!.E+ A675 ?6 75+ ?,+ Appendix a Specifications NATUser Guide Glossary User Guide Ipaq Connection Point CP-2W User Guide Ipaq Connection Point CP-2W User Guide Ipaq Connection Point CP-2W

Related manuals

Manual 2 pages 7.29 Kb