York DJ 180 warranty Guide Specifications, General

Page 37

261660-YTG-C-0707

GUIDE SPECIFICATIONS

GENERAL

Units shall be manufactured by York International Unitary Products Group in an ISO 9001 certified facility.

York's Sunline Magnum™ units are convertible single pack- age units. All models have dual independent refrigerant cir- cuits for efficient part load operation and maximum comfort control. Although the units are primarily designed for curb mounting on a roof, they can also be slab-mounted at ground level or set on steel beams above a finished roof. Cooling only, cooling with gas heat and cooling with electric heat models are available with a wide variety of factory-mounted options and field-installed accessories to make them suitable for almost every application. All units are self-contained and assembled on full perimeter base rails with holes in the four corners for overhead rigging. Every unit is completely piped, wired, charged and tested at the factory to simplify the field installation and to provide years of dependable operation. All models (including those with an economizer) are suitable for either bottom or horizontal duct connections. Models with power exhaust are suitable for bottom duct connections only. For bottom duct, remove the sheet metal panels from the supply and return air openings through the base of the unit. For horizontal duct, replace the supply and return air panels on the rear of the unit with a side duct flange accessory. All supply air blowers are equipped with a belt drive that can be adjusted to meet the exact requirements of the job.

Each unit shall have 4 condenser fan motors. A high static drive option is available for applications with a higher CFM and/or static pressure requirement. All compressors include crankcase heat and internal pressure relief. Every refrigerant circuit includes an expansion valve, a liquid line filter-drier, a discharge line high pressure switch and a suction line with a freezestat and low pressure/loss of charge switch. The unit control circuit includes a 75 VA transformer, a 24-volt circuit breaker and a relay board with two compressor lockout cir- cuits, a terminal strip for thermostat wiring, plus an additional set of pin connectors to simplify the interface of additional field controls. All units have long lasting powder paint cabinets with 1000 hour salt spray test approval under ASTM-B117 proce- dures. All 208/230 and 460-volt models are ETL approved. All 208/230 and 575-volt models are CGA approved. All models include a 1-year limited warranty on the complete unit. Com- pressors and electric heater elements carry an additional 4- year warranty. Aluminized steel tubular heat exchangers carry an additional 9-year warranty.

DESCRIPTION

Units shall be factory-assembled, single packaged, DJ***N Electric Cooling/Gas Heat, DJ***C/E Electric Cooling/ Optional Electric Heat, designed for outdoor mounted instal- lation. The 15,17.5, and 20 ton units shall have minimum EER ratings of 11.1. The 25 ton unit shall have a minimum EER rating of 10.5.

They shall have built-in field convertible duct connections for down discharge supply/return or horizontal discharge supply/ return, and be available with factory installed options or field installed accessories. The units shall be factory wired, piped, charged with R-22 refrigerant and factory tested prior to ship- ment. All unit wiring shall be both numbered and color coded. All units shall be manufactured in a facility certified to ISO 9001 standards and the cooling performance shall be rated in accordance with DOE and ARI test procedures. Units shall be ETL & CGA listed, classified to ANSIZ21.47 standards, UL 1995/CAN/CSA No. 236-M90 conditions.

UNIT CABINET

Unit cabinet shall be constructed of G90 galvanized steel, with exterior surfaces coated with a non-chalking, powdered paint finish, certified at 1000 hours salt spray test per ASTM-B117 standards. Indoor blower section shall be insulated with a min- imum 1/2" thick insulation, coated on the airside. Aluminum foil faced insulation shall be used in the furnace compartment and be fastened with ridged fasteners to prevent insulation from entering the air stream. Cabinet panels shall be "large" size, easily removable for servicing and maintenance. Full perimeter base rails shall be provided to assure reliable transit of equip- ment, overhead rigging and proper sealing on roof curb appli- cations. Disposable 2" filters shall be furnished and be accessible through a removable access door, sealed airtight. Units filter track shall be designed to accommodate either 1" or 2" filters. Fan performance measuring ports shall be provided on the outside of the cabinet to allow accurate air measure- ments of evaporator fan performance without removing panels or creating air by-pass of the coils. Condensate pan shall be internally sloped and conform to ASHRAE 62-89 self-draining standards. Condensate connection shall be a minimum of 1" I.D. female and be a ridged mount connection. Unit shall incor- porate a fixed outdoor air damper with an outdoor air intake opening covered with a bird screen and a rain hood painted to match the exterior of the unit.

INDOOR (EVAPORATOR) FAN ASSEMBLY

Fan shall be a belt drive assembly and include an adjustable- pitch motor pulley. Job site selected (B.H.P.) brake horsepower shall not exceed the motors nameplate horsepower rating, plus the service factor. Units shall be designed not to operate above service factor. Fan wheel shall be double-inlet type with for- ward-curved blades, dynamically balanced to operate smoothly throughout the entire range of operation. Airflow design shall be constant air volume.

A variable air volume (VAV) option using a variable frequency drive (VFD) is available for applications requiring a constant supply duct static pressure. Units equipped for VAV shall be controlled by a duct pressure transducer with a 0 - 5” WC pres- sure range. The pressure transducer shall provide a 0 - 5 VDC output signal to a VAV control board which, in turn shall provide a 2 - 10 VDC speed reference signal to the VFD. The VAV con- trol board shall operate using factory-installed Supply Air, Return Air and Outside Air Temperature Sensors. Units equipped with VFD’s shall have factory-installed manual bypass as an option.

Unitary Products Group

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Description Technical GuideTable of Contents Ton Magnum Model Number Nomenclature Product NomenclatureFeatures Unit Cutaway FACTORY-INSTALLED OptionsUnitary Products Group FIELD-INSTALLED Accessories Unitary Products Group Capacity Ratings ARI Sound Power RATING1GAS Heat Ratiings MBH Cooling Capacities for DJ1806500 Cooling Capacities for DJ2108000 Cooling Capacities for DJ240Cooling Capacities for DJ300 AIR Temp Altitude Feet Altitude Correction FactorsALTITUDE/TEMPERATURE Conversion Factor Volt and Standard Drive Volt Standard Drive 6000 7000 8000 9000 9400 965 980 1025 1065 1125 1170 870 900 930 950 980 995 1015 6000 7000 8000 9000 9400 7500 8750 10000 11250 12500 Blower Motor and Drive Data Power Exhaust PerformanceStatic RESISTANCES1 Size DJ Electrical Data Without Powered Convenience Outlet240 DJ Electrical Data with Powered Convenience Outlet None 120.4 150 E18 13.5 37.5 Physical Data DJ Voltage LIMITATIONS1Electric Heat Correction Factors Supply FAN VFD WEIGHTS, in LBSFront View Dimensions Utilities Entry Data Rear View Dimensions Minimum Clearances Unit Dimensions DJ180, 210, 240 & 300 RainhoodUnit Center of Gravity Four and SIX Point Loads Dimension Unit Roof Curb DimensionsOCC General Guide SpecificationsOutdoor Condenser FAN Assembly Electric Heating DJ***C/E Models Other Factory Installed Options

DJ 180 specifications

York DJ 180 is a cutting-edge DJ controller that has made a significant impact on the electronic music scene, particularly among novice and professional DJs alike. Designed to offer a seamless mixing experience, it combines innovative technology and user-friendly features, making it a go-to choice for anyone looking to elevate their DJ skills.

One of the standout features of the York DJ 180 is its intuitive layout, which includes two robust jog wheels that offer excellent precision and responsiveness. These jog wheels are not only sensitive to touch but also offer adjustable resistance, allowing DJs to customize their setup according to their mixing style. The controller's large play/pause and cue buttons are positioned strategically for quick access, ensuring smooth transitions between tracks.

The DJ 180 also boasts a comprehensive array of controls, including eight backlit performance pads per deck. These pads allow users to trigger samples, loops, and effects effortlessly, enabling enhanced creativity on the fly. Additionally, the controller features dedicated EQ knobs and a built-in sound card, which allows for easy connection to external devices and enhanced audio quality.

Incorporating advanced technology, the York DJ 180 supports both USB and MIDI connections, ensuring compatibility with a wide range of software and hardware setups. Whether mixing with popular DJ software or using it as a standalone controller for live performances, this flexibility makes it an essential tool for any DJ.

Another notable characteristic of the York DJ 180 is its portability. Weighing in at just under six pounds and featuring a slim profile, it is designed for DJs on the move, making it easy to transport to gigs and events without compromising on functionality.

Furthermore, the controller includes built-in effects, such as delay, reverb, and flanger, allowing DJs to add unique touches to their sets without needing external equipment. This streamlined approach makes the York DJ 180 not just a controller but a complete performance solution.

In conclusion, the York DJ 180 is a technologically advanced DJ controller that balances portability and performance with user-friendly features. Whether you are just starting your DJ journey or are an experienced professional, the versatility and quality of the York DJ 180 make it an excellent choice for all music enthusiasts.
Top Page Image Contents