United States Stove 2941 owner manual Locating the Heater, Description Qty

heater or chimney connector. The 1 inch air space provides free air circulation. It is essential that there be openings at the top and bottom of these clearance reducers so cool air can enter at the bottom and hot air exit at the top. It is the "chimney effect" whereby when the air in the space is heated, it rises exiting from the top and being replaced by cooler air at the bottom, that makes these shields effective.

Masonry, or other non-combustible products, attached directly to a combustible surface without an air space offer very little protection and cannot be considered a clearance reducer unless specified materials have been tested and listed for direct attachment to a combustible surface. The same applies to thin veneer brick and stone coverings. These materials provide adequate protection only when mounted on sheet metal with a 1 inch spacing to the wall.

A variety or prefabricated clearance reduction systems which have been tested and listed are available through heater dealers. Always look for a safety listing label on the product when selecting a clearance reduction system and make sure it is designed for solid fuel appliances. The manufactures of these systems provide specific installation instructions that must be followed exactly for a safe installation.

LOCATING THE HEATER

AS A LOCATION IS SELECTED,

KEEP THE FOLLOWING IN MIND:

1.The chimney connection should be as airtight as possible. The heater must have its own chimney flue. Do not connect this unit to a chimney flue serving another appliance. If there is no chimney near where you wish to place the heater, you can use a UL 103HT Residential Type and Building Heating Appliance Chimney (Fig. 5, 6, 6A & 6B).

2.Place the heater on solid masonry or solid concrete. When the heater is used on a combustible floor protector of one layer of 3/8" millboard having a thermal conductivity of K=0.84 BTU in./ft. 2 hr. Deg. F with 28-gauge sheet metal or a UL Listed floor protector. Have the floor protector extend 16" beyond the door side of the heater and under the connector pipe in the back.

3.Check Figures 2, 3, and 4. Be sure you have the clearances shown from the heater and the connector pipe to combustible surfaces. If you have a solid brick or stone wall behind your heater, you can place the heater as close as you wish to the wall. If the wall is only faced with brick or stone, treat it as a combustible wall.

	26"
Fig. 2			25"
	WONDERWOOD		Fig. 3
			35"
		16"	12"

54"	NON-COMBUSTIBLE
	CONSTRUCTION IN
	ACCORDANCE WITH
12"	NFPA 211

Fig. 4		36"
		19 1/4"
		NOTE: DASHED LINES SHOW
		STRAIGHT UP AND THROUGH
		THE WALL INSTALLATION
32 1/4"	16"	4 3/4"
17"

SIDEWALL FLOOR PROTECTOR (TOP VIEW)

REPAIR PARTS LIST - MODEL 2941 (SEE PAGE 18)

AUTOMATIC WOOD BURNING CIRCULATOR

Key No.	Description	Qty.	Part No.
1	Heat Jacket Assembly	1	68619
2	Base Weldment	1	67859
3	Smoke Curtain	1	22090
*	Smoke Curtain Bracket	2	22171
4	Flue Collar	1	40246
5	Flue Collar Gasket	1	88032
6	Draft Damper Frame	1	40075
7	Draft Control Damper	1	23476
8	Draft Damper Hinge Pin	1	17200
9	Clip Spring	1	83818
10	Fire Grate	2	40076
11	Liner	3	40100
12	Firebrick	10	89066
13	Top Brick Retainer	2	40132
	Feed Door Assembly		68621
	Ash Door Assembly		68620
14	Feed Door	1	40199
15	Ash Door	1	40289
16	Door Latch	2	22108
17	Door Handle	2	40091
18	Feed Door Rope Gasket	3.75FT	88033
19	Ash Door Rope Gasket	2.5FT	88033
20	1/4-20 Kep Nut	2	83250
21	5/16 ID, 3/4 OD Washer	2	83045
22	Latch Spacer	2	21467
23	Door Hinge Pin (Short)	1	83872
24	Door Hinge Pin (Long)	1	23441
25	Heat Shield	1	23475
26	Drop Wooden Handle	1	89523
27	Ash Pan	1	67444
28	Solid Damper	1	D6
29	Top Liner	1	23474
30	Heat Shield	1	22110
31	Secondary Heat Shield	1	22030
*	NOT SHOWN

4 17