Venting Requirements, Pellet Vent Type | United States Stove 6110

Installation

VENTING REQUIREMENTS

Install vent at clearances specified by the vent manufacturer.

Do not connect the pellet vent to a vent serving any other appliance or furnace.

Do not install a flue damper in the exhaust venting system of this unit.

The following installation guidelines must be followed to ensure conformity with both the safety listing of this furnace and to local building codes.

IMPORTANT! This unit is equipped with a negative draft system that pulls air through the burn pot and pushes the exhaust out of the dwelling. If this unit is connected to a flue system other than the way ex- plained in this manual, it will not function properly.

MAXIMUM VENTING DISTANCE

Installation MUST include at least 3-feet of vertical pipe. This will create some natural draft to reduce the possibility of smoke or odor during appliance shutdown and keep exhaust from causing a nuisance or hazard by exposing people or shrubs to high temperatures. The maximum recommend vertical venting height is 12-feet for 3-inch type “PL” vent. Total length of horizontal vent MUST NOT exceed 4-feet. Use no more than 180 degrees of elbows (two 90-degree elbows, or two 45-degree and one 90-degree elbow, etc.) to maintain adequate draft.

PELLET VENT TYPE

A UL listed 3-inch or 4-inch type “PL” pellet vent exhaust system must be used for installation and attached to the pipe connector provided on the back of the furnace (use a 3-inch to 4-inch adapter for 4-inch pipe). Use 4-inch vent if the vent height is over 12-feet or if the installation is over 2,500 feet above sea level.

We recommend the use of Simpson Dura-Vent®or Metal-Fab®pipe (if you use other pipe, consult your local building codes and/or building inspectors). Do not use Type-B Gas Vent pipe or galvanized pipe with this unit. The pellet vent pipe is designed to disassemble for cleaning and should be checked several times during the burning season. Pellet vent pipe is not furnished with the unit and must be purchased separately.

PELLET VENT INSTALLATION

The installation must include a clean-out tee to enable collection of fly ash and to permit periodic cleaning of the exhaust system. 90-degree elbows accumulate fly ash and soot thereby reducing exhaust flow and performance of the furnace. Each elbow or tee reduces draft potential by 30% to 50%.

All joints in the vent system must be fastened by at least 3 screws, and all joints must be sealed with HI-TEMP RTV silicone sealant to be airtight. The area where the vent pipe penetrates to the exterior of the home must be sealed with silicone or other means to maintain the vapor barrier between the exterior and the interior of the home.

Vent surfaces can get hot enough to cause burns if touched by children. Noncombustible shielding or guards may be required.

PELLET VENT TERMINATION

Do not terminate the vent in an enclosed or semi-enclosed area, such as; carport, garage, attic, crawl space, under a sundeck or porch, narrow walkway, or any other location that can build up a concentration of fumes.

The termination must exhaust above the outside air inlet elevation.

The termination must not be located where it will become plugged by snow or other materials.

USSC

6110 specifications

The United States Stove 6110 is a highly regarded wood-burning stove known for its efficiency and versatility. Designed to provide both warmth and a welcoming ambiance, this stove is ideal for homeowners seeking a reliable heating solution. Its classic design combines a functional aesthetic with advanced technology, making it a favorite among consumers.

One of the standout features of the United States Stove 6110 is its impressive heat output. With a heating capacity of up to 2,200 square feet, this stove can effectively warm large areas, making it suitable for both living rooms and larger open spaces. It achieves this through a robust firebox that holds a generous amount of wood, allowing for extended burn times and reducing the frequency of refueling.

The stove incorporates a secondary combustion system designed to maximize efficiency. This technology ensures that the gases produced during the burn process are effectively consumed before being released into the atmosphere. As a result, the 6110 demonstrates lower emissions while maximizing heat output—a critical factor for environmentally conscious consumers. Additionally, the unit boasts an EPA certification, affirming its compliance with strict emissions regulations.

Another significant characteristic of the United States Stove 6110 is its construction. Made from high-quality materials, the stove features heavy-duty steel that ensures durability and longevity. The cast iron door is another highlight, providing a classic look while offering a large viewing area to enjoy the beauty of the flames while maintaining heat retention.

The versatility of the 6110 is further enhanced by its adjustable air intake system, which allows users to control the burn rate and heat output according to their needs. This feature not only improves fuel efficiency but also empowers users to customize their heating experience, making it an ideal choice for various climates and personal preferences.

In terms of safety, the stove is equipped with a firebrick-lined interior that enhances heat retention and protects the exterior surfaces from overheating. This ensures that the stove operates safely and efficiently, minimizing the risks associated with wood burning.

Overall, the United States Stove 6110 combines exceptional heating performance, advanced technology, and classic design, making it a standout choice for anyone looking to enhance their home’s warmth and comfort. Whether for a cozy cabin or a family home, this stove promises reliable and efficient heating for many winters to come.