Cabinet Door Knob Assembly

FIREPLACE INSTALLATION

Connection of the stovepipe directly into the existing masonry chimney over the fireplace opening is the only approved method. This installation performs bet- ter, yielding easy to clean and inspect for creosote. Before beginning this type of installation plan carefully; a high de- gree of skill is required to insure safety.

An entry port for the stovepipe must be cut through the chimney with minimum damage to the fire clay liner. Some involved measurements may be required to locate the flue liner exactly. Before cutting, take time to mark the size and position of the entry port. Position the entry port so that at least 8 inches of the flue liner remains below the port.

Keep in mind that wood mantels and combustible trim around the fireplace must have adequate clearances from the heater and stovepipe or must be protected in an approved manner. Also, be sure to leave at least 24" clearance between the top of the stovepipe and the combustible ceiling or other com- bustibles. Placing the center of the entry port 2 feet below the ceiling will insure proper clearance for 6 inch, 8 inch, and 10 inch stovepipes. Next, install a fire clay (at least 5/8 in. thick) or metal thimble, being sure that the thimble is flush with the inner flue lining. Secure the thimble in place with refractory mor- tar. The thimble should be surrounded on all sides with 8 inches of brickwork (solid masonry units) or 24 inches of stone.

Install the stovepipe as far as possible into the thimble, but not past the inside of the flue lining. There should be a small air space (approximately 1/2 in.) between the stovepipe and thimble, allowing for expansion of the stove- pipe. Seal this airspace with high-tem- perature caulking or ceramic wool. Fi- nally, be sure to wire the damper closed and apply the same sealant you used at the stovepipe and thimble junction.

Do not vent up through the fireplace opening, regardless of whether the fire- place opening is closed.

MASONRY CHIMNEYS have several positive attributes: If properly built, they are quite durable, and most homeowners consider them more at- tractive perhaps than a non-enclosed factory built chimney.

And, if the chimney is located within the confines of the house (that is, not at- tached to an exterior wall), its mass alone will store heat longer and con- tinue to release the heat long after the fire has died. Masonry chimneys have many disadvantages though.

Masonry chimneys constructed on an exterior wall are exposed to cold out- door temperatures, promoting greater heater loss, higher accumulations of creosote, and reduced draft which leads to poorer heater or furnace perfor- mance.

The door knob is mounted inside of the cabinet door to facilitate shipping and must be reversed for proper usage.

To get cabinet door open, place hand under cabinet frame (right hand side of cabinet door) and push door out.

INSTALL THE CABINET DOOR KNOB USING THE STEPS BELOW:

1.Remove the machine screw and door knob (Fig. 9).

2.Place door knob on outside of cabinet door. Then place machine screw through hole and into door knob and tighten (Fig. 10).

MACHINE

SCREW

CABINET DOOR

KNOB

FIG. 9

FIG. 10

2931 specifications

The United States Stove 2931 is a remarkable wood-burning stove that combines efficiency, style, and functionality, making it an excellent choice for homeowners seeking an effective heating solution. Designed with both aesthetics and performance in mind, this stove has garnered a reputation for its reliability and ease of use.

One of the key features of the U.S. Stove 2931 is its efficient heating capacity. With a maximum heating capacity of up to 2,000 square feet, it is perfect for medium to large-sized spaces. The stove is designed to provide long burn times, ensuring that your home stays warm and cozy even during the coldest winter nights. Users can expect an impressive burn time that can stretch up to 8 hours, depending on the type of wood used and the load size.

The stove is constructed from heavy-duty cast iron and steel, providing durability and extended service life. Its robust build ensures that it can withstand high temperatures, while also allowing for better heat retention. The combination of materials also enhances the overall aesthetic appeal of the stove, making it a stylish addition to any room.

One of the standout technologies integrated into the U.S. Stove 2931 is the unique air control system. This system allows users to easily regulate the airflow into the stove, enhancing combustion efficiency. By controlling the air intake, homeowners can optimize the burn rate, extending fuel efficiency and significantly reducing smoke emissions. This not only contributes to a cleaner environment but also ensures that the stove meets stringent EPA guidelines.

Additionally, the U.S. Stove 2931 features a large viewing window, allowing users to enjoy the visual ambiance of the flames while also monitoring the fire's behavior. This glass window is designed to withstand high temperatures and is positioned for optimal visibility, adding a welcoming touch to the living space.

The stove is equipped with an easily accessible ash pan, simplifying the cleaning process. This feature ensures that maintenance is hassle-free, allowing users to spend more time enjoying the comforting warmth of their stove and less time on upkeep.

In conclusion, the United States Stove 2931 is a well-crafted, efficient wood-burning stove that offers a combination of functionality, durability, and style. With its impressive heating capacity, effective air control system, and user-friendly design, this stove is an ideal choice for anyone looking to enhance their home heating experience.