United States Stove 5660(I) manual Operating Instructions ‐

Page 10
Control Board Functions:
Figure 3

OPERATING INSTRUCTIONS ‐ continued

MODE Button: The MODE button allows you to switch operating mode on your Pellet Stove Room Heater. Depress the MODE button to switch between Manual and T‐STAT modes. As you depress the MODE button the indicator light above the desired mode will engage. When you engage the Manual mode, you will be able to manually select the heat settings. If you have installed a remote thermostat for your Pellet Stove Room Heater and wish to have the heater controlled by that thermostat, depress the MODE button to engage T‐ STAT mode. The thermostat will control the heat output of the Heater alternating between the lowest heat level and the highest heat level that you have pre‐selected.

The T‐STAT mode provides the most even heat output, for better comfort, and to extend the life of the pellet fuel ignition system. Additionally, the constant flame serves as a warning for people and pets to keep away from the heater while it is in operation.

ON/OFF Button: The ON/OFF button is used to turn the heater on and off. Whenever there is power to the heater, the LED indicator light above the ON/OFF button will be solid red. If the heater is cold prior to start‐up, press and release the ON/OFF button. The LED light above the ON/OFF button will alternately flash red and green to indicate the startup cycle has started. Fuel pellets will start to feed into the burn pot and the pellet fuel ignition system will be activated. Flames in the burn pot will normally appear between 4 ‐ 8

minutes, and once the flame has been established, the startup cycle will end, this takes between 8‐12 minutes. At this point the LED indicator light above the ON/OFF button will glow solid green. The user will now be able to make heat level adjustments.

HEAT LEVEL Button: Depress the HEAT LEVEL button to advance the heat level by one level until you reach the maximum setting; from the maximum level you will decrease one level each time you depress the HEAT LEVEL button. The circulation fan speed will also increase with the heat level setting. Wait until the startup cycle is complete and the ON/OFF LED is solid green to set Heat Level. (The HEAT LEVEL LEDs are also used as codes to indicate a malfunction, please refer to the Safety Features and warning codes section for more information.)

FAN Button: Depressing the FAN button will set the circulation fan speed to high, overriding the automatic fan speed control. The onboard logic will modulate the fan speed in accordance with the heat level setting. It is recommended that you allow the control to automatically set and adjust the speed of the fan to obtain optimum efficiency and minimal fan noise.

AUGER Button: Whenever Operating the Pellet Stove for First Time, or if The Stove Runs Out Of Pellets, it is Necessary to Prime the Auger with Pellet Fuel. To do this, Press and Hold the AUGER Button for Approximately 3 Seconds until the AUGER LED illuminates. This Procedure will prime the Auger and then Automatically Initiate the Normal Ignition Cycle. NOTICE: Do not use this procedure for normal startup. To do so would cause excessive fuel build‐up in the burn pot.

AUGER TRIM Button: This Button is only enabled when operating at Heat Level 1. Depress the AUGER TRIM Button to change the Auger feed rate on the minimum heat level; to account for the quality of pellet fuel being used. Increasing

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation and Operating Manual Models Table of Contents Introduction Safety Information USE of Solid Wood Fuel is Prohibted by LAWSafety Information ‐ Specifications DimensionsDimensions ‐ Pre‐start Check‐up Operating InstructionsCheck and Fill the Fuel Hopper with Pellets Lighting InstructionsCirculation Air Flow Operating Instructions ‐Auger Auger TrimOperating Instructions ‐ Safety Features and warning code Thermostat Installation Installation of Remote ThermostatClearances to Combustibles Installing Your Room Heater Installing Your Room Heater ‐ Horizontal Exhaust Vent InstallationInstalling Your Room Heater ‐ Freestanding Interior Vertical Installation Freestanding Exterior Vertical Installation Page Selkirk DIRECT‐TEMP Vent System for Pellet Stove Heaters UP & OUT Horizontal Termination KIT Straight OUT Horizontal Termination KIT Through the Roof Vertical Termination KIT Mobile Home Installation Insert Pellet Stove Installation Insert Pellet Stove Installation ‐ Minimum Clearance to Combustibles and Floor Protection Floor ProtectionInstallation into a Masonry Fireplace Vent Termination Locations Maintenance Burn PotAsh Removal ‐ Insert Unit Maintenance ‐Ash Removal ‐ Freestanding Unit Disposal of AshesCleaning Chimney/Vent System Cleaning Door GasketsTrouble Shooting Heater Flame keeps going out on LOW setting Trouble Shooting ‐200oF High‐limit switch has tripped Auger motor does not function normallyTrouble Shooting ‐ Wiring Diagram Replacement Parts Stove BrightLimited Warranty

5660(I) specifications

The United States Stove 5660(I) is a powerful pellet stove designed to provide efficient heating while boasting modern features and a user-friendly interface. Known for its high performance and reliability, this stove is a popular choice for homeowners seeking an effective heating solution for their living spaces.

One of the standout features of the 5660(I) is its capacity to produce up to 50,000 BTUs, making it suitable for heating areas up to approximately 2,500 square feet. This impressive heating capacity ensures that even larger rooms can be warmed quickly and efficiently, contributing to energy savings and comfort during the colder months.

The stove operates primarily on wood pellets, which are an environmentally friendly fuel choice. Wood pellets are made from compressed sawdust and provide a renewable heating source that burns cleanly and efficiently. The use of pellets not only minimizes emissions but also allows the stove to deliver consistent heat output.

In terms of technology, the United States Stove 5660(I) incorporates advanced features to enhance user experience. The stove is equipped with a digital control panel, offering easy programming options for both heating schedules and temperature settings. This digital interface allows homeowners to customize heating preferences, ensuring a comfortable atmosphere without excessive manual adjustments.

Another notable characteristic of the 5660(I) is its large hopper capacity, holding up to 60 pounds of pellets. This feature extends the time between refueling sessions, allowing for more extended periods of operation without interruption. The stove also features an automatic ignition system, simplifying the startup process and making it convenient for users.

The design of the 5660(I) is not just about functionality; it also boasts an aesthetic appeal. With its sleek and contemporary look, it can seamlessly integrate into various home decors. The stove comes in multiple finishes, allowing homeowners to choose a model that best matches their style.

Safety is also a priority with the United States Stove 5660(I). The unit includes various safety features, including an automatic shut-off function in case of a malfunction, ensuring peace of mind while the stove is in use. The high-efficiency burn system minimizes the amount of ash produced, making maintenance less of a chore.

In summary, the United States Stove 5660(I) combines performance, efficiency, and aesthetic appeal, presenting an excellent heating solution for any home. Its advanced features, ease of use, and eco-friendly fuel choice make it a top contender in the pellet stove market. Whether for heating a large living area or creating a cozy atmosphere, the 5660(I) is a dependable choice.
Top Page Image Contents