United States Stove 5660(I) manual Freestanding Interior Vertical Installation

Page 17

INSTALLING YOUR ROOM HEATER ‐ continued

FREESTANDING INTERIOR VERTICAL INSTALLATION

1.Locate your Pellet Stove Room Heater in a location which meets the requirements of this manual, but in an area where it does not interfere with the house framing, wiring, etc.

2.Install a non‐combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front of the unit.

3.Place your Pellet Stove Room Heater on the hearth pad and locate the unit in manner that will leave the exhaust vent with a minimum of 3” (75mm) clearance to any combustible wall.

4.When installing the air intake, locate the center of the combustion air intake pipe at the back of your unit. Line up the center with the same spot on your exterior wall and cut a 2‐1/2” (64mm) diameter hole through the wall.

5.Secure all vent joint connections with 3 screws. Seal the exhaust vent joint connections with high temperature silicone sealant.

6.Install the combustion air intake pipe.

7.Install a tee, with a cleanout, on the exhaust pipe found at the rear of your unit.

8.Install approved vent upward through the ceiling. When you pass through the combustible framing ensure that the appropriate ceiling firestop is used. You must maintain a minimum 3” (75mm) clearance to combustibles and keep any insulation away from the exhaust vent.

9.Extend the exhaust vent through the roof flashing and ensure that the vertical cap is approximately 36” (900mm) above the roof.

17

Image 17
Contents Installation and Operating Manual Models Table of Contents Introduction USE of Solid Wood Fuel is Prohibted by LAW Safety InformationSafety Information ‐ Dimensions SpecificationsDimensions ‐ Check and Fill the Fuel Hopper with Pellets Operating InstructionsPre‐start Check‐up Lighting InstructionsAuger Operating Instructions ‐Circulation Air Flow Auger TrimOperating Instructions ‐ Safety Features and warning code Installation of Remote Thermostat Thermostat InstallationClearances to Combustibles Installing Your Room Heater Horizontal Exhaust Vent Installation Installing Your Room Heater ‐Installing Your Room Heater ‐ Freestanding Interior Vertical Installation Freestanding Exterior Vertical Installation Page Selkirk DIRECT‐TEMP Vent System for Pellet Stove Heaters UP & OUT Horizontal Termination KIT Straight OUT Horizontal Termination KIT Through the Roof Vertical Termination KIT Mobile Home Installation Insert Pellet Stove Installation Insert Pellet Stove Installation ‐ Floor Protection Minimum Clearance to Combustibles and Floor ProtectionInstallation into a Masonry Fireplace Vent Termination Locations Burn Pot MaintenanceAsh Removal ‐ Freestanding Unit Maintenance ‐Ash Removal ‐ Insert Unit Disposal of AshesCleaning Door Gaskets Chimney/Vent System CleaningTrouble Shooting 200oF High‐limit switch has tripped Trouble Shooting ‐Heater Flame keeps going out on LOW setting Auger motor does not function normallyTrouble Shooting ‐ Wiring Diagram Stove Bright Replacement PartsLimited Warranty

5660(I) specifications

The United States Stove 5660(I) is a powerful pellet stove designed to provide efficient heating while boasting modern features and a user-friendly interface. Known for its high performance and reliability, this stove is a popular choice for homeowners seeking an effective heating solution for their living spaces.

One of the standout features of the 5660(I) is its capacity to produce up to 50,000 BTUs, making it suitable for heating areas up to approximately 2,500 square feet. This impressive heating capacity ensures that even larger rooms can be warmed quickly and efficiently, contributing to energy savings and comfort during the colder months.

The stove operates primarily on wood pellets, which are an environmentally friendly fuel choice. Wood pellets are made from compressed sawdust and provide a renewable heating source that burns cleanly and efficiently. The use of pellets not only minimizes emissions but also allows the stove to deliver consistent heat output.

In terms of technology, the United States Stove 5660(I) incorporates advanced features to enhance user experience. The stove is equipped with a digital control panel, offering easy programming options for both heating schedules and temperature settings. This digital interface allows homeowners to customize heating preferences, ensuring a comfortable atmosphere without excessive manual adjustments.

Another notable characteristic of the 5660(I) is its large hopper capacity, holding up to 60 pounds of pellets. This feature extends the time between refueling sessions, allowing for more extended periods of operation without interruption. The stove also features an automatic ignition system, simplifying the startup process and making it convenient for users.

The design of the 5660(I) is not just about functionality; it also boasts an aesthetic appeal. With its sleek and contemporary look, it can seamlessly integrate into various home decors. The stove comes in multiple finishes, allowing homeowners to choose a model that best matches their style.

Safety is also a priority with the United States Stove 5660(I). The unit includes various safety features, including an automatic shut-off function in case of a malfunction, ensuring peace of mind while the stove is in use. The high-efficiency burn system minimizes the amount of ash produced, making maintenance less of a chore.

In summary, the United States Stove 5660(I) combines performance, efficiency, and aesthetic appeal, presenting an excellent heating solution for any home. Its advanced features, ease of use, and eco-friendly fuel choice make it a top contender in the pellet stove market. Whether for heating a large living area or creating a cozy atmosphere, the 5660(I) is a dependable choice.