ASRock 980DE3/U3S3 manual CPU Fan Connectors

Page 23

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header	Please connect the chassis
(4-pin SPEAKER 1)	speaker to this header.
(see p.12 No. 26)

Power LED Header	Please connect the chassis
(3-pin PLED1)	power LED to this header to
(see p.12 No. 25)	indicate system power status.
	The LED is on when the system
	is operating. The LED keeps
	blinking in S1 state. The LED is
	off in S3/S4 state or S5 state
	(power off).

Chassis and Power Fan Connectors	Please connect the fan cables
(4-pin CHA_FAN1)	to the fan connectors and
(see p.12 No. 12)	match the black wire to the
	ground pin.
(4-pin PWR_FAN1)
(see p.12 No. 2)

CPU Fan Connectors	FAN_SPEED_CONTROL
(4-pin CPU_FAN1)	CPU_FAN_SPEED
(see p.12 No. 3)	+12V
(see p.12 No. 3)	GND
	1	2	3	4

Please connect the CPU fan cable to the connector and match the black wire to the ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

23

Image 23

Contents

980DE3/U3S3 Disclaimer Copyright NoticeContents Bios Setup Utility Introduction Package ContentsSpecifications Hardware ConnectorUSB Support CDFCC, CE, Whql CertificationsASRock Intelligent Energy Saver Unique FeaturesASRock Instant Boot ASRock OC TunerASRock XFast LAN ASRock OC DNAASRock APP Charger ASRock XFast USBASRock X-Boost ASRock XFast RAMMotherboard Layout LAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Break Installing a DimmPcie Slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Description Jumpers SetupSATAII6 Onboard Headers and ConnectorsSerial ATA Sata Data Cable System Panel Header CPU Fan Connectors ATX 12V Power Connector ATX Power ConnectorHot Plug and Hot Swap Functions for SATA2 / SATA3 HDDs What is Hot Plug Function?What is Hot Swap Function? Points of attention, before you process the Hot Plug Sata / SATA2 / SATA3 HDD Hot Plug Feature Operation GuideHow to Hot Unplug a Sata / SATA2 / SATA3 HDD How to Hot Plug a Sata / SATA2 / SATA3 HDDMake a Sata / SATA2 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up BiosUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Introduction Bios Menu BarSystem Time HourMinuteSecond Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen Processor Maximum Voltage AMD C-State SupportProcessor Maximum Frequency North Bridge Maximum FrequencyDram Frequency Memory Configuration Memory ClockMemory Timing Power Down Enable HT Bus WidthWould you like to save current setting user defaults? Command RateChipset Settings NB Voltage +1.8V Power VoltageInstant Flash Advanced ScreenEnhance Halt State C1E CPU ConfigurationCool ‘n’ Quiet Secure Virtual MachineOnboard Lan Chipset ConfigurationOnboard HD Audio Front PanelAcpi Configuration Acpi Hpet table Onboard SATA3 Operation Mode Storage ConfigurationSata Operation Mode Sata IDE Combined ModePCI IDE BusMaster PCIPnP ConfigurationPCI Latency Timer Floppy Configuration Super IO Configuration USB Configuration Hardware Health Event Monitoring Screen CPU Fan SettingChassis Fan 1 Setting Boot Settings Configuration Boot ScreenSecurity Screen Exit Screen Drivers Menu Install Operating SystemSupport CD Information Running The Support CD

Related manuals

Manual 52 pages 35.35 Kb