ASRock A75M-ITX manual Dual Monitor and Surround Display Features, Dual Monitor Feature

Page 21

2.6 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal VGA output sup- port (D-Sub and HDMI), you can easily enjoy the benefits of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for D-Sub and HDMI to support dual VGA output so that D-sub and HDMI can drive same or different display contents.

To enable dual monitor feature, please follow the below steps:

1.Connect D-Sub monitor cable to D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel.

D-Sub port

HDMI port

2.If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefits of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer.

21

Image 21
Contents A75M-ITX Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Bios Feature ConnectorUnique Feature Rear Panel I/OHardware MonitorCertifications Page Page Page ATXPWR1 Motherboard LayoutI/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules Dimm Expansion Slot PCI Express Slot Installing an expansion cardAMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureWhat is HDCP? For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OSHdcp Function CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsFront Panel Audio Header CPU Fan Connectors ATX Power ConnectorSupply to this connector ATX 12V Power Connector Please connect an ATX What is Hot Plug Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Timing Control Power Down Enable Dram Configuration Dram FrequencyMultiplier/Voltage Change CPU Frequency MultiplierCommand Rate CR RAS# to CAS# Delay tRCDWrite Recovery Time tWR RAS to RAS Delay tRRDWould you like to save current setting user defaults? CPU Load-Line CalibrationSB Voltage Instant Flash Advanced ScreenCore C6 Mode CPU ConfigurationPackage C6 Mode Cool ‘n’ QuietPrimary Graphics Adapter North Bridge ConfigurationShare Memory Onboard Hdmi HD AudioSouth Bridge Configuration Sata Mode Storage ConfigurationSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Acpi Configuration Acpi Hpet table USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Support CD Information Install Operating SystemRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 157 pages 40.08 Kb