ASRock A75M-ITX manual Boot Screen

Page 53

3.6 Boot Screen

In this section, it will display the available devices on your system for you to config- ure the boot settings and the boot priority.

Setup Prompt Timeout

This shows the number of seconds to wait for setup activation key. 65535(0xFFFF) means indefi nite waiting.

Bootup Num-Lock

If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

Full Screen Logo

Use this item to enable or disable OEM Logo. The default value is [Enabled].

AddOn ROM Display

Use this option to adjust AddOn ROM Display. If you enable the option “Full Screen Logo” but you want to see the AddOn ROM information when the system boots, please select [Enabled]. Configuration options: [Enabled] and [Disabled]. The default value is [Enabled].

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN feature.

Boot Failure Guard

Enable or disable the feature of Boot Failure Guard.

Boot Failure Guard Count

Enable or disable the feature of Boot Failure Guard Count.

53

Image 53

Contents A75M-ITX Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Bios Feature ConnectorUnique Feature Rear Panel I/OCertifications HardwareMonitor Page Page Page ATXPWR1 Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slot PCI Express Slot Installing an expansion cardWhat does an AMD Dual Graphics system include? AMD Dual Graphics Operation GuideEnjoy the benefit of AMD Dual Graphics AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureHdcp Function What is HDCP?For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsFront Panel Audio Header Supply to this connector CPU Fan ConnectorsATX Power Connector ATX 12V Power Connector Please connect an ATX What is Hot Plug Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Set up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Timing Control Power Down Enable Dram Configuration Dram FrequencyMultiplier/Voltage Change CPU Frequency MultiplierCommand Rate CR RAS# to CAS# Delay tRCDWrite Recovery Time tWR RAS to RAS Delay tRRDSB Voltage Would you like to save current setting user defaults?CPU Load-Line Calibration Instant Flash Advanced ScreenCore C6 Mode CPU ConfigurationPackage C6 Mode Cool ‘n’ QuietPrimary Graphics Adapter North Bridge ConfigurationShare Memory Onboard Hdmi HD AudioSouth Bridge Configuration Sata Mode Storage ConfigurationSata IDE Combined Mode Sata ControllerSerial Port Address Super IO ConfigurationSerial Port Acpi Configuration Acpi Hpet table USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportHardware Health Event Monitoring Screen CPU Fan 1 & 2 SettingChassis Fan 1 Setting Boot Screen Security Screen Exit Screen Support CD Information Install Operating SystemRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB

Related manuals

Manual 157 pages 40.08 Kb