ASRock A75M-ITX North Bridge Configuration, Primary Graphics Adapter, Share Memory, Dual Graphics

Page 45

3.4.2 North Bridge Configuration

Primary Graphics Adapter

This item will switch the PCI Bus scanning order while searching for video card. It allows you to select the type of Primary VGA in case of multiple video controllers. The default value of this feature is [PCI Express]. Con- figuration options: [Onboard] and [PCI Express].

Share Memory

This allows you to set the share memory feature. The default value is [Auto]. Configuration options: [Auto], [32MB], [64MB], [128MB], [256MB] and [512MB].

Onboard HDMI HD Audio

This allows you to enable or disable the “Onboard HDMI HD Audio” fea- ture.

Dual Graphics

This item appears only when you install AMD RADEON HD6670 / 6570

/6450 graphics card on this motherboard. Use this to enable or disable Dual Graphics feature. If you enable this option, the primary monitor will be onboard VGA. If you select [Auto], Dual Graphics function will be auto- matically enabled when you install AMD RADEON HD6670 / 6570 / 6450 graphics card. The default value is [Auto].

45

Image 45
Contents A75M-ITX Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Bios Feature ConnectorUnique Feature Rear Panel I/OHardware MonitorCertifications Page Page Page ATXPWR1 Motherboard LayoutI/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slot PCI Express Slot Installing an expansion cardAMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureWhat is HDCP? For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OSHdcp Function CIR sensors in different angles ASRock Smart Remote Installation GuideDescription Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsFront Panel Audio Header CPU Fan Connectors ATX Power ConnectorSupply to this connector ATX 12V Power Connector Please connect an ATX What is Hot Plug Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Timing Control Power Down Enable Dram Configuration Dram FrequencyMultiplier/Voltage Change CPU Frequency MultiplierCommand Rate CR RAS# to CAS# Delay tRCDWrite Recovery Time tWR RAS to RAS Delay tRRD Would you like to save current setting user defaults? CPU Load-Line Calibration SB Voltage Instant Flash Advanced ScreenCore C6 Mode CPU ConfigurationPackage C6 Mode Cool ‘n’ QuietPrimary Graphics Adapter North Bridge ConfigurationShare Memory Onboard Hdmi HD AudioSouth Bridge Configuration Sata Mode Storage ConfigurationSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Acpi Configuration Acpi Hpet table USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Support CD Information Install Operating SystemRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 157 pages 40.08 Kb