ASRock 990FX Extreme4 manual Front USB 3.0 Panel Installation Guide

Page 35

IEEE 1394 Header

(9-pin FRONT_1394)

(see p.12 No. 15)

GND

+12V +12V

RXTPBM_0 RXTPBP_0

GND GND

RXTPAM_0 RXTPAP_0 1

Besides one default IEEE 1394 port on the I/O panel, there is one IEEE 1394 header (FRONT_1394) on this motherboard. This IEEE 1394 header can support one IEEE 1394 port.

Serial port Header

RRXD1

(9-pin COM1)

DDTR#1

DDSR#1

 

CCTS#1

(see p.12 No.31)

 

 

1

 

RRI#1

 

RRTS#1

 

GND

 

TTXD1

 

DDCD#1

This COM1 header supports a serial port module.

HDMI_SPDIF Header

HDMI_SPDIF header, providing

(2-pin HDMI_SPDIF1)

SPDIF audio output to HDMI

(see p.12 No. 1)

VGA card, allows the system to

 

connect HDMI Digital TV/

 

projector/LCD devices. Please

 

connect the HDMI_SPDIF

 

connector of HDMI VGA card to

 

this header.

Front USB 3.0 Panel Installation Guide

Step 1

Prepare the bundled Front USB 3.0 Panel, four HDD screws, and six chassis screws.

Step 2

Screw the 2.5” HDD/SSD to the Front USB 3.0 Panel with four HDD screws.

Step 3

Intall the Front USB 3.0 Panel into the 2.5” drive bay of the chassis.

Step 4

Screw the Front USB 3.0 Panel to the drive bay with six chassis screws.

35

Image 35
Contents 990FX Extreme4 Disclaimer Copyright NoticeContents Super IO Configuration Acpi Configuration USB Configuration Install Operating SystemUefi Menu Bar CPU ConfigurationIntroduction Package ContentsSpecifications USB ConnectorSmart Switch Hardware Bios FeatureUnique Feature Support CDPage Page Page Designed in Taipei Motherboard LayoutTable for Audio Output Connection I/O PanelLAN Port LED Indications Page Pre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmInstalling a Dimm Pcie Slots Installing an expansion cardExpansion Slots PCI and PCI Express Slots Requirements Slitm and Quad Slitm Operation GuideDouble-click Nvidia Settings icon on your Windows taskbar Driver Installation and SetupFor Windows XP / XP 64-bit OS For Slitm mode only Select Control Panel tab Select Nvidia Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows 7 / VistaTM OS Install the required drivers to your systemFor Windows XP OS \ Surround Display Information Surround Display FeatureClear Cmos Jumper Jumpers SetupJumper Setting Onboard Headers and Connectors USB 2.0 Headers Serial ATA3 ConnectorsUSB 3.0 Header Besides two default USB Optional wireless transmittingFront Panel Audio Header Internal Audio Connectors This connector allows youCD-ROM, DVD-ROM, TV Tuner card, or Mpeg cardPower off Power LED Header Please connect the chassisPower LED to this header to Indicate system power statusPlease connect an ATX Power supply to this connector CPU Fan ConnectorsATX Power Connector ATX 12V Power ConnectorFront USB 3.0 Panel Installation Guide USB 3.0 Panel Rear USB 3.0 Bracket Installation GuideSmart Switches Status Code Description 11 Dr. DebugPage Page Page Hot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Make a SATA3 Driver Diskette Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions Set up UefiMake a SATA3 driver diskette by following .16.1 on Use RAID Installation Guide to set RAID configuration\ RAID Installation Guide Make a SATA3 Driver Diskette Installing Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Uefi Menu Bar IntroductionSystem Time HourMinuteSecond Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen HT Bus Width Dram Timing Control Power Down EnableMultiplier/Voltage Change HT Bus SpeedRAS to RAS Delay tRRD RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRCPU Load-line calibration Would you like to save current setting user defaults?NB Voltage HT VoltageInstant Flash Advanced ScreenEnhance Halt State C1E CPU ConfigurationCool ‘n’ Quiet Secure Virtual MachinePrimary Graphics Adapter North Bridge ConfigurationSouth Bridge Configuration Storage Configuration Hard Disk S.M.A.R.T Onboard IDE & 1394 ControllerSuper IO Configuration Acpi Configuration Acpi Hpet table USB Mouse Power OnLegacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerChassis Fan 3 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 2 SettingBoot Screen Security Screen Exit Screen Drivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB
Related manuals
Manual 281 pages 46.81 Kb