Panasonic SC-BTT490 owner manual Troubleshooting guide, General operation, Cannot eject disc

Troubleshooting guide

Before requesting service, please perform the following steps.

(For the U.S.A. and Canada)

Do you have the latest firmware installed? Firmware updates may be released to correct

operating irregularities that are discovered with certain movies. (> 19)

4

Make the following checks and visit our website for more information.

For U.S.A.:

www.panasonic.com/help

Enter the model number.

For Canada:

http://www.panasonic.ca

4

Or visit our website to find a service center. You can find a service center near you easily

on our website.

Other support information:

“Customer Services Directory (United States and Puerto Rico)” (> 54) or “Limited Warranty (Only for CANADA)” (> 55).

(For units with PX printed on the packaging)

Do you have the latest firmware installed?

Firmware updates may be released to correct operating irregularities that are discovered with certain movies. (> 19)

Even so, you still have trouble, consult your dealer.

The following do not indicate a problem with this unit:

–Regular disc rotating sounds.

–Image disturbance during search.

–Image disturbance when replacing 3D discs.

∫Unit doesn’t respond to remote control or front panel buttons.

Press and hold [Í/I] on the main unit for 3 seconds.

–If still unable to power the unit off, disconnect the power cord, wait 1 minute, then reconnect the power cord.

∫Cannot eject disc.

The unit may have a problem.

1While the unit is off, press and hold [OK], [B]

and [Y] on the remote control at the same time for more than 5 seconds.

–“00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “06 FTO” is displayed on the unit’s display.

3Press [OK] on the remote control or [< OPEN/CLOSE] on the unit.

General operation

To return to the factory preset.

¾Select “Yes” in “Restore Default Settings” in the Setup menu. (> 40)

To return all settings to the factory preset.

¾Reset the unit as follows:

1While the unit is off, press and hold [OK], [B]

and [Y] on the remote control at the same time for more than 5 seconds.

–“00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “08 FIN” is displayed on the unit’s display.

3Press and hold [OK] on the remote control or

[< OPEN/CLOSE] on the unit for at least 3 seconds.

This unit is turned off when the input for the TV is switched.

¾This is a normal phenomenon when using VIERA Link (HDAVI Control 4 or later). For details please read the operating instructions for the TV.

The remote control doesn’t work properly.

¾Change the batteries in the remote control. (> 8)

¾The remote control and main unit are using different codes. If “SET ” is displayed on the unit’s display when a button is pressed on the remote control, change the code on the remote control. (> 40, 48)

The TV tuner mode is not displayed when the TV is switched on.

¾This phenomenon may occur, depending on the TV setting, when “Quick Start” is set to “On”.

¾Depending on the TV, this phenomenon may be prevented by reconnecting the HDMI cable to a different HDMI input terminal or by changing the HDMI auto connection setting.

You have forgotten your ratings password. You want to cancel the ratings level.

¾The ratings level returns to the factory preset.

1 While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same time for more than 5 seconds.

–“00 RET” is displayed on the unit’s display.

2 Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “03 VL” is displayed on the unit’s display.

3 Press [OK] on the remote control or [< OPEN/CLOSE] on the unit.

44 VQT3X49