Panasonic SC-BTT490 owner manual Picture

This unit does not recognize the USB connection correctly.

¾Disconnect and reconnect the USB cable. If it still does not recognize the connection, turn the power of this unit off and on again.

¾If you connect USB HDD to this unit, use USB extension cable that is supplied with the HDD.

The unit switches to standby mode.

¾This unit will automatically turn to standby mode after 30 minutes if it is inactive. (> 21)

¾When the time set for the sleep timer has passed, the power will be turned off. (> 8)

¾One of the unit’s safety devices is activated. Press [Í/I] on the main unit to turn the unit on.

The unit does not turn off.

1Press and hold [Í/I] on the main unit for 5 seconds. (If still unable to power the unit off, disconnect the power cord, wait 1 minute,

then reconnect the power cord.)

2Reset the unit as follows:

While the unit is off, press and hold [+ VOLUME], [< OPEN/CLOSE] and [Í/I] on the main unit at the same time for more than 5 seconds.

Picture

The images from this unit do not appear on the TV. Picture is distorted.

Jittering occurs.

¾An incorrect resolution is selected in “HDMI

Resolution”. Reset the setting as follows:

1While the unit is on, press and hold [OK], [B] and [Y] on the remote control at the same

time for more than 5 seconds.

–“00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “04 PRG” is

displayed on the unit’s display.

3Press and hold [OK] on the remote control or

[< OPEN/CLOSE] on the unit for at least 3 seconds. Set the item again. (> 36)

–When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream, select “Yes” in “Restore Default

Settings” and make proper settings. (> 40)

¾When “3D BD-Video Playback” in the Setup menu is set to “Auto”, images may not be output depending on the connection method. After removing the disc from this unit, select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. (> 37)

¾If irregular coloring occurs on your TV, turn the TV off for about 30 minutes.

If it persists, move the speakers further away from the TV.

Video is not output.

¾Set “High Clarity Sound” in the Setup menu to “Disable” to use the VIDEO OUT terminal. (> 37)

Video is not output in high-definition.

¾Confirm that “HDMI Resolution” in the Setup menu is set properly. (> 36)

3D video is not output.

¾Change the settings as required by the connected TV format. (> 37, “3D Type”)

¾Are the settings on this unit and the TV correct? (> 24)

¾Depending on the connected TV, the video being played back might switch to 2D video due to changes in resolution etc. Check the 3D setting on the TV.

¾Check that proper HDMI video input is selected on the TV.

3D video is not output correctly as 2D.

¾Select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. (> 37, “3D BD-Video Playback”)

¾Discs that have recorded titles with Side by side (2 screen structure) and that can be enjoyed in 3D are played back in accordance with the settings of the TV.

No subtitles.

¾When progressive output is on, closed captions/subtitles cannot be displayed.

The subtitles overlap closed captions recorded on discs.

¾Turn off the subtitles or the closed caption setting on the TV. (> 32)

A black band is displayed around the edge of the screen.

The aspect ratio of the screen is abnormal.

¾Confirm the “TV Aspect” is set properly. (> 39)

¾Adjust the aspect setting on the television.

Reference

VQT3X49 45