ASRock p4fsb1333-650 manual USB 2.0 Headers

Page 20

USB 2.0 Headers

USB_PWR

(9-pin USB6_7)

P-7

P+7

 

GND

(see p.10 No. 17)

DUMMY

 

 

1

 

GND

 

P+6

 

P-6

 

USB_PWR

(9-pin USB4_5)

USB_PWR

(see p.10 No. 18)

P-4

P+4

 

GND

 

DUMMY

Besides four default USB 2.0 ports on the I/O panel, there are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

1

GND P+5

P-5

USB_PWR

Infrared Module Header

+5VSB

 

IRTX

(5-pin IR1)

DUMMY

 

(see p.10 No. 29)

1

GND

 

 

IRRX

This header supports an optional wireless transmitting and receiving infrared module.

Internal Audio Connector

(4-pin CD1)

 

(CD1: see p.10 No. 23)

CD1

 

CD-L GND GND CD-R

Front Panel Audio Header

 

 

GND

 

 

 

 

 

PRESENCE#

(9-pin HD_AUDIO1)

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.10 No. 21)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This connector allows you to receive stereo audio input from sound sources such as

aCD-ROM, DVD-ROM, TV tuner card, or MPEG card.

This is an interface for front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.Enter BIOS Setup Utility. Enter Advanced Settings, and then select Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled].

2 0

Image 20
Contents P4FSB1333-650 Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Connector Bios FeatureSee Caution Support CDDDRII533*, DDRII667 VGA Motherboard Layout 22.9cm 9.0HD 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Land CPU Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI, Hdmr and PCI Express SlotsJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header Serial port Header Sataii Hard Disk Setup Guide Western DigitalUntied Overclocking Technology Driver Installation GuideHdmr Card and Driver Installation Bios Menu Bar Advanced Screen Navigation KeysMain Screen CPU Configuration Enhance Halt State Max Cpuid Value LimitIntel R Virtualization tech CPU Thermal ThrottlingChipset Configuration Internal Graphics Mode Select Dvmt Mode SelectDram RAS# Precharge Dram RAS# Activate to PrechargeFront Panel CD-InOnBoard Lan PCI Fix FunctionAcpi Configuration IDE Configuration ATA/IDE ConfigurationIDE Device Configuration ATA/IDE Configuration EnhancedLBA/Large Mode PIO ModeDMA Mode Block Multi-Sector TransferPCIPnP Configuration PCI Latency TimerA.R.T Bit Data TransferFloppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Configuration Target CPU Temperature C Hardware Health Event Monitoring ScreenCPU Quiet Fan Tolerance CBoot Screen Boot Settings ConfigurationBoot From Onboard LAN Boot Up Num-LockSecurity Screen Main Advanced Monitor BootChange Supervisor Password Load Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers Menu