ASRock p4fsb1333-650 manual Hardware Health Event Monitoring Screen, CPU Quiet Fan, Tolerance C

Page 38

3.4 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

 

BIOS SETUP UTILITY

 

 

 

Main

Advanced

H/W Monitor

Boot

 

Security

Exit

Hardware Health Event Monitoring

 

Target Fan Speed

 

 

 

 

 

 

 

 

 

 

Fast

 

 

CPU Temperature

 

: 37 C / 98 F

 

Middle

 

M / B Temperature

 

: 31 C / 87 F

 

Slow

 

 

CPU Fan Speed

 

: 3400 RPM

 

 

 

 

Chassis Fan Speed

 

: N / A

 

 

 

 

Vcore

 

 

: 1.629V

 

 

 

 

+ 3.30V

 

 

: 3.306V

 

 

 

 

+ 5.00V

 

 

: 5.067V

 

 

Select Screen

 

+ 12.00V

 

: 11.890V

 

 

 

 

 

 

Select Item

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

General Help

 

CPU Quiet Fan

 

[Enabled]

 

F9

Load Defaults

 

Target CPU Temperature (

C)

[50]

 

F10

Save and Exit

 

Tolerance ( C)

 

[02]

 

ESC

Exit

 

Target Fan Speed

 

[Fast]

 

 

 

 

 

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

 

CPU Quiet Fan

This item allows you to identify the temperature of CPU fan. If you set this option as [Disabled], the CPU fan will operate in full speed. If you set this option as [Enabled], you will find the items “Target CPU Temperature

( C)”, “Tolerance ( C)”, and “Minimun Fan Speed” appear to allow you adjusting them. The default value is [Disabled]. You are allowed to enable this function only when you install 4-pin CPU fan.

Target CPU Temperature ( C)

The target temperature will be between 45 C and 65 C. The default value is [50].

Tolerance ( C)

The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C.

Target Fan Speed

Use this option to set the target fan speed. You can freely adjust the target fan speed according to the target CPU temperature that you choose. The default value is [Fast]. Configuration options: [Fast], [Middle] and [Slow].

3 8

Image 38
Contents P4FSB1333-650 Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications See Caution ConnectorBios Feature Support CDDDRII533*, DDRII667 VGA Motherboard Layout 22.9cm 9.0HD 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Land CPU Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI, Hdmr and PCI Express SlotsJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header Serial port Header Sataii Hard Disk Setup Guide Western DigitalUntied Overclocking Technology Driver Installation GuideHdmr Card and Driver Installation Bios Menu Bar Advanced Screen Navigation KeysMain Screen CPU Configuration Intel R Virtualization tech Enhance Halt StateMax Cpuid Value Limit CPU Thermal ThrottlingChipset Configuration Dram RAS# Precharge Internal Graphics Mode SelectDvmt Mode Select Dram RAS# Activate to PrechargeOnBoard Lan Front PanelCD-In PCI Fix FunctionAcpi Configuration IDE Device Configuration IDE ConfigurationATA/IDE Configuration ATA/IDE Configuration EnhancedDMA Mode LBA/Large ModePIO Mode Block Multi-Sector TransferA.R.T PCIPnP ConfigurationPCI Latency Timer Bit Data TransferOnBoard Floppy Controller Floppy ConfigurationSuper IO Configuration Serial Port AddressUSB Configuration CPU Quiet Fan Target CPU Temperature CHardware Health Event Monitoring Screen Tolerance CBoot From Onboard LAN Boot ScreenBoot Settings Configuration Boot Up Num-LockSecurity Screen Main Advanced Monitor BootChange Supervisor Password Save Changes and Exit Load Optimal DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers Menu