ASRock p4fsb1333-650 Floppy Configuration, Super IO Configuration, OnBoard Floppy Controller

Page 36

3.3.6 Floppy Configuration

In this section, you may configure the type of your floppy drive.

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Floppy Configuration

 

Select the type of

 

 

floppy drive

Floppy A

[1.44 MB 312"]

connected to the

 

 

system.

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

3.3.7 Super IO Configuration

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Configure Super IO Chipset

 

Allow BIOS to Enable

 

 

or Disable Floppy

OnBoard Floppy Controller

[Enabled]

Controller.

 

 

Serial Port Address

[3F8 / IRQ4]

 

 

Infrared Port Address

[Disabled]

 

 

Parallel Port Address

[378]

 

 

Parallel Port Mode

[ECP + EPP]

 

 

EPP Version

[1.9]

 

 

ECP Mode DMA Channel

[DMA3]

 

 

Parallel Port IRQ

[IRQ7]

 

 

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.

Serial Port Address

Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3].

Infrared Port Address

Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].

3 6

Image 36
Contents P4FSB1333-650 Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Connector Bios FeatureSee Caution Support CDDDRII533*, DDRII667 VGA Motherboard Layout 22.9cm 9.0HD 8CH I/O Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Land CPU Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI, Hdmr and PCI Express SlotsJumpers Setup PS2USBPWR1Onboard Headers and Connectors IDE1USB 2.0 Headers Chassis Speaker Header Serial port Header Sataii Hard Disk Setup Guide Western DigitalDriver Installation Guide Hdmr Card and Driver InstallationUntied Overclocking Technology Bios Menu Bar Navigation Keys Main ScreenAdvanced Screen CPU Configuration Enhance Halt State Max Cpuid Value LimitIntel R Virtualization tech CPU Thermal ThrottlingChipset Configuration Internal Graphics Mode Select Dvmt Mode SelectDram RAS# Precharge Dram RAS# Activate to PrechargeFront Panel CD-InOnBoard Lan PCI Fix FunctionAcpi Configuration IDE Configuration ATA/IDE ConfigurationIDE Device Configuration ATA/IDE Configuration EnhancedLBA/Large Mode PIO ModeDMA Mode Block Multi-Sector TransferPCIPnP Configuration PCI Latency TimerA.R.T Bit Data TransferFloppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Configuration Target CPU Temperature C Hardware Health Event Monitoring ScreenCPU Quiet Fan Tolerance CBoot Screen Boot Settings ConfigurationBoot From Onboard LAN Boot Up Num-LockMain Advanced Monitor Boot Change Supervisor PasswordSecurity Screen Load Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers Menu