MSI AM-690E manual Chassis Intrusion Connector JCASE1, IDE Connector IDEB1

Page 27

Hardware Setup

Connector

Chassis Intrusion Connector: JCASE1

This connector connects to the chassis intrusion switch cable. If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record.

CINTRU 1

GND 2

JCASE1

IDE Connector: IDEB1

This connector supports IDE hard disk drives, optical disk drives and other IDE devices.

IDEB1

Important

If you install two IDE devices on the same cable, you must configure the drives separately to master / slave mode by setting jumpers. Refer to IDE device’s documentation supplied by the vendors for jumper setting instructions.

2-9

Image 27

Contents MS-9826 V1.X Mainboard AM-690ETechnical Support Copyright NoticeTrademarks Revision HistorySafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-9826Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Product Overview Mainboard Specifications Form Factor MountingEnvironmental Block Diagram AM-690E MS-9826 v1.X Mini ITX Mainboard Mainboard LayoutBoard Dimension Back Panel & I/O Shield Drawing ODD Power ConsumptionRFI Safety Compliance & MtbfPage Hardware Setup HDPWR1 Quick Components GuideCPU Central Processing Unit CPU Installation Procedures for Socket AM2 Installing AMD Socket AM2 CPU Cooler Set Memory Installing Memory ModulesPower Supply System/CPU Power Connector JPW1HDD Power Connector HDPWR1 Back Panel Connector Chassis Intrusion Connector JCASE1IDE Connector IDEB1 SATA1 SATA2 Serial ATA II Connector SATA1, SATA2Front Panel Connector JFP1 Fan Power Connectors CPUFAN1, SYSFAN1SPI Flash ROM Connector JSPI1 I2C Bus Connector J1Clear Cmos Jumper JBAT1 JumperSlot PCI Peripheral Component Interconnect SlotPCI Interrupt Request Routing Bios Setup Press Del to enter Setup Entering SetupMain Menu Control KeysGetting Help General Help F1Menu Bar System Date AMI BIOS, Processor, System MemoryMain System TimeAdvanced CPU ConfigurationBios Setup Microcode Update IDE Configuration OnBoard PCI IDE ControllerPrimary/Third/Fourth IDE Master/Slave Super IO Configuration Smart Fan Configuration Bios Setup Serial Port1 AddressCpufan PWM Control Cpufan Mode SettingAcpi Settings MS-9826 Mainboard CPU FAN TypeAdvanced Acpi Configuration Acpi Version Features Bios Setup General Acpi Configuration C1E SupportMS-9826 Mainboard Event Log Configuration View Event Log Mark All Events As ReadClear Event Log Bios Setup MPS Configuration MPS Revision USB Configuration Legacy USB Support MS-9826 Mainboard Smbios Configuration Smbios Smi SupportUSB Mass Storage Device Configuration Emulation Type USB 2.0 Controller modePlug and Play O/S PCI Latency TimerPCIPnP Clear NvramBoot Settings Configuration BootBootup Num-Lock MS-9826 Mainboard Quick BootQuiet Boot AddOn ROM Display ModeSecurity Supervisor Password / Change Supervisor PasswordUser Password / Change User Password Boot Sector Virus ProtectionChipset NorthBridge ConfigurationDram BG Scrub Bios Setup ECC Configuration Dram ECC EnableBit ECC Mode Dram Scrub RedirectOnChip Sata Type OnChip Sata ChannelOnboard LAN Boot ROM Bios Setup Onboard Peripherals Configuration Spread SpectrumPower Exit Page System Resources Software code Sioidx equ 4EH SIODTAequ 4FH Watch Dog Timer SettingAMI Post Code Bootblock Initialization Code CheckpoinitsCheckpoint Description MS-9826 Mainboard Post Code CheckpointsFree area in F000h segment with 0FFh Resource List SB600 Gpio ConfigSB600 GPM Config MS-9826 Mainboard Map Port Description Dev. ID Bus# System Resources PCI DevicesMS-9826 Mainboard SMBus Resource Allocation ISA Interrupt AllocationISA DMA Channel Allocation