NuTone PFC-56II, PFC-48II Important Safeguards, Upper Canopy Down ROD Lower Wires Bushing

HOW TO ASSEMBLE (FIGURE 1 shows fan parts.)

1.	Locate upper canopy and remove two (2) screws holding fan
	mounting bracket in canopy.
2.	Locate down rod and remove spring bushing from hole inside of
	rod and remove set screw from down rod.
3.	(FIGURE 3) Place upper canopy and lower canopy on down
	rod by placing upper canopy over down rod with open end to-
	ward plastic ball hanger. Place lower canopy over down rod with
	open end facing away from plastic ball hanger.
4.	Replace spring bushing into hole inside of down rod.
5.	(FIGURE 4) Thread the wire from the bushing through the down
	rod by feeding the white, black and green supply wires from
	motor through the bushing in the down rod and up through the
	down rod.
6.	Remove cotter pin from bolt on motor shaft. Remove nut, wash-
	ers and bolt from motor shaft. Slide end of down rod over plastic
	sleeve on motor shaft so that holes in down rod line up with hole
	in motor shaft. (Replace bolt, flat washer, lockwasher, nut and

UPPER

CANOPY

DOWN

ROD

LOWER	FIGURE 3
CANOPY

WIRES

BUSHING

WIRES

FIGURE 4

	cotter pin). IMPORTANT: Tighten nut until lockwasher is fully
	compressed. No play or wiggle should be evident between the
	down rod and the shaft. Bend out ends of cotter pin to secure.
	Replace and tighten set screw into down rod that was removed
	from Step 2.
7.	Position lower canopy over motor shaft and wiring until it stops
	and secure with set screw.
8.	Blades may be installed at this time.
	PFC-48 /PFC-56Remove the two screws, lockwashers, and
	blade support bracket from motor housing. Leave fiber board
	gasket in place on motor housing. Place blade, with mounting
	bracket up, over the gasket and replace the screws, lockwashers,
	and blade support bracket. Tighten securely. Repeat for each
	blade.
9.	Place black rubber spacers in between the fan hanger bracket
	and the 4” metal box. Mount the fan hanger bracket to the 4” box
	marked for fan support. Use the mounting screws or hardware
	provided with the ceiling box. IMPORTANT: The ceiling box must
	be marked as acceptable for fan support. The box should be
	securely fastened to the structure so that it will support at least 35
	lbs. Supply wiring, 120V, 60 Hz, should be run through a wall
	switch to the outlet box.
10.Lift fan and place the ball hanger of the fan into the mounting
	bracket. Rotate down rod until slot in ball hanger engages tab of
	mounting bracket.
11. Cut off excess length of motor leads allowing 6” of lead to extend
	into the outlet box. Strip leads approximately 1/4”.
12.	(FIGURE 2) Connect fan leads to house supply wires using Listed
	wire connectors. Connect white to white, black to black, and green
	ground wires from fan and from mounting bracket to the supply
	ground. After splice connections are made, turn splices upward
	and carefully push into outlet box with green and white leads on
	one side of the box and the black leads on the other side of the
	box.
13.	(FIGURE 5) Raise the upper canopy up to the mounting bracket
	and secure using the two screws removed earlier.
14.Restore electrical power and check for proper operation of the
	fan.

IMPORTANT SAFEGUARDS

1.Be sure fan is switched off before cleaning it.

2.Keep hands, clothing and other objects away from moving fan blades.

3.Exercise close supervision of children if they are present when fan is operating.

4.Shut off electricity to fan before servicing or working near fan.

5.Do not operate fan if it has been damaged in any manner. Contact your nearest NuTone Authorized Service Center.

UPPER

CANOPY

FIGURE 5

Two Year Limited Warranty

WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of two (2)) years from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this two year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the two year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.

WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

Date of InstallationBuilder or Installer

Model No. and Product Description

IF YOU NEED ASSISTANCE OR SERVICE:

For the location of your nearest NuTone Independent Authorized Service Center:

Residents of the contiguous United States Dial Free 1-800-543-8687

Please be prepared to provide:

Product model number • Date and Proof of purchase • The nature of the difficulty Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.

Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.

Rev. 03/2001

99524445B