Raypak PS-4 PS-8 Optional Wireless Remote Display/Keypad, Optional Base Receiver

Page 10

3.See “Electrical Wiring” (page 17) for instructions on running the cable from theAqua Logic main unit to the remote display/keypad.

Pull up on bottom edge

to remove cover

Optional Wireless Remote Display/Keypad

The Aqua Logic Wireless Remote Display/Keypad (Goldline part number AQL-REMOTE-RF-PS-x) must be mounted indoors or in a weather protected area (rain should never hit the display/keypad). Note that number of outputs on the remote (eg “4” or “8”) must match the outputs on the Aqua Logic main control unit. There is no limit on the number of wireless remotes that can be installed. The display/keypad can be mounted directly onto any wall surface. When selecting a location, note that the maximum distance between the wireless remote and the base receiver on theAqua Logic main control unit is 600 feet (200m) line of site or 200 feet (65m) through walls, etc. If in doubt about the distance, test operation before installing the remote.Also, note that the remote must be within 6 feet of a standard 120V wall outlet for the plug-in power supply (supplied as part of the wireless remote display/keypad). Follow the steps below:

1.Remove the display/keypad baseplate from the cover by lifting up on the cover at the lower end of the keypad. See diagram above.

2.Screw the baseplate in the desired position (screws supplied by installer).

3.Connect to supplied 9 volt plug-in power supply.

Optional Base Receiver

The optional base receiver (Goldline part numberAQL-BASE-RF) must be installed if either the wireless remote display/keypad or the wireless spaside remote is used. To install the base receiver, simply remove the knockout on the upper left side of theAqua Logic main control unit, insert the base receiver, and then tighten the nut from the inside. Also refer to the manual for the Base Receiver and the diagram on page 18 of this manual.

Optional Valve Actuators

For actuators supplied with the Aqua Logic—refer to the Jandy instructions included in the kit with the actuators. Note that the internal cams in the actuator may also have to be adjusted depending on the way the actuator is mounted on the valve and the desired valve action.

Standard Plumbing and Actuator Mounting

RETURNSUCTION

OUT

OUT IN

IN

IN

7

OUT

(Common)

(Common)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Aqua Logic Important Safety Instructions Table of Contents What’s Included Before installing the Aqua Logic SystemBefore You Begin What’s not IncludedPlumbing Requirements Installation StepsElectrical Requirements General Water Chemistry Water ChemistrySalt Salt LevelGallons Liters Optional Wired Remote Display/Keypad Temperature SensorsAqua Logic Control Center Optional Base Receiver Optional Wireless Remote Display/KeypadOptional Valve Actuators Plumbing General Pool EquipmentFlow Switch Turbo CellElectrical Wiring Main Service Power to the Circuit Breaker SubpanelGrounding and Bonding Circuit Breaker Installation and WiringAqua Logic Control Power General Purpose OutletHigh Voltage 120/240V Pool Equipment 240 VAC 120 VACValveActuators Low Voltage WiringHeater Control Generic Heaters Laars Heaters most models except LXHayward Heaters Pentair/Purex/MiniMaxRaypak RP2100 Pool/Spa Heater STA-RITE HeaterTemperature Sensors Wired Remote Display/KeypadBase Receiver Flow SwitchTurbo Cell To access the Configuration Menu Accessing the Configuration MenuConfiguration Menu Items ChlorinatorHeater Cooldown Heater1Heater Name Heater ExtendSolar Priority SolarSolar Extend Pool/SpaLights Name Spa SpilloverFilter Operation Lights FunctionAux1 Name Aux1 FunctionValve3 Name Aux1 InterlockAux1 Freeze Protection Valve3 FunctionValve3 Interlock Valve3 Freeze ProtectionProgram Automatic Operation Before StartupHeater Checkout Industry Canada Statement FCC StatementInterference Limited Warranty-Pool Automation & Chlorination Products Aqua Logic Programming Flow Chart

PS-4 PS-8 specifications

Raypak, a leader in the heating and water temperature control industry, offers a robust line of products featuring state-of-the-art technology and efficiency. Among its notable offerings are the Raypak PS-4 and PS-8 models, which are designed to meet a variety of heating demands in residential and commercial settings.

The Raypak PS-4 and PS-8 are both part of the Performance Series and are designed for versatility. These models utilize high-efficiency gas burners that not only maximize heat output but also minimize fuel consumption. This efficiency is crucial for both cost savings and environmental sustainability, making these heaters an excellent choice for mindful consumers and businesses.

One of the standout features of the PS-4 and PS-8 is their user-friendly digital display, which provides real-time information about system performance. This allows users to easily monitor and adjust settings, ensuring optimal operation at all times. Additionally, these models come equipped with advanced diagnostics that aid in troubleshooting and maintenance, reducing downtime and improving overall system reliability.

The PS-4 model has a heating capacity of up to 400,000 BTU, while the PS-8 boasts an impressive capacity of 800,000 BTU. This wide range of output makes them suitable for a variety of applications, from residential pools to large commercial facilities. Both models feature a durable, rust-resistant cabinet designed to withstand the elements, further enhancing their longevity and performance.

In terms of technology, both heaters are designed with an innovative control system that allows for precise temperature management. Additionally, they feature a built-in fan, which helps distribute heat evenly throughout the space. This ensures that users enjoy consistent temperatures, whether in a pool or spa setting.

The PS-4 and PS-8 models also focus on safety, incorporating multiple safety mechanisms such as high limit sensors and a robust electronic ignition system. These features help prevent issues such as overheating and ensure the system operates safely and reliably.

In conclusion, the Raypak PS-4 and PS-8 models exemplify modern engineering in the heating industry. With their combination of high efficiency, advanced technology, and user-friendly design, they are excellent choices for anyone looking to improve their heating solutions in both residential and commercial applications. Whether for pool heating or spa use, the Raypak heaters promise reliability, performance, and long-lasting service.
Top Page Image Contents