Raypak PS-4 PS-8 installation manual Hayward Heaters, Pentair/Purex/MiniMax

Page 18

Hayward Heaters

Refer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “Remote Control Connections” and the diagram on the following page:

1.Turn off power to heater

2.WireAqua Logic to terminals 1 & 2 (see diagram)

3.Leave jumper attached to terminals 4 & 5

4.Move “BYPASS” dipswitch on heater circuit board to “ON” position (up)

5.Turn heater power back on

6.Switch heater to either “Pool” or “Spa” (it doesn’t make any difference which is selected, the Aqua Logic will take control)

7.Heater display should be “bO” (for “bypass On)

8.Heater will fire wheneverAqua Logic requests (whenAqua Logic “Heater” LED is illuminated)

ºC ON

ºF OFF

Dipswitch located on heater circuit board

PK

W

R

BK

R

Pool/Spa

Air

Solar

Heater1

Heater2

Do not remove jumper

Terminal block located at electrical junction box

Pentair/Purex/MiniMax

1.Turn power off to heater

2.Remove factory installed jumper from the “Ext Switch” connector.

3.Wire theAqua Logic to the “Ext Switch” connector as shown below

4.The wires to the Aqua Logic must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the heater.

5.Set the Power (Thermostat Select) switch to either “Pool” or “Spa”

6.Set the “Pool” and “Spa” thermostats to their maximum settings.

Remove

Factory Jumper

Ext.

Switch

MINIMAX

Pool/Spa

Air

Solar

Heater1

Heater2

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Aqua Logic Important Safety Instructions Table of Contents What’s Included Before installing the Aqua Logic SystemBefore You Begin What’s not IncludedInstallation Steps Plumbing RequirementsElectrical Requirements General Water Chemistry Water ChemistrySalt Salt LevelGallons Liters Temperature Sensors Optional Wired Remote Display/KeypadAqua Logic Control Center Optional Wireless Remote Display/Keypad Optional Base ReceiverOptional Valve Actuators Plumbing General Pool EquipmentFlow Switch Turbo CellElectrical Wiring Main Service Power to the Circuit Breaker SubpanelGrounding and Bonding Circuit Breaker Installation and WiringAqua Logic Control Power General Purpose OutletHigh Voltage 120/240V Pool Equipment 240 VAC 120 VACLow Voltage Wiring ValveActuatorsHeater Control Generic Heaters Laars Heaters most models except LXHayward Heaters Pentair/Purex/MiniMaxRaypak RP2100 Pool/Spa Heater STA-RITE HeaterTemperature Sensors Wired Remote Display/KeypadFlow Switch Base ReceiverTurbo Cell To access the Configuration Menu Accessing the Configuration MenuConfiguration Menu Items ChlorinatorHeater Cooldown Heater1Heater Name Heater ExtendSolar Priority SolarSolar Extend Pool/SpaLights Name Spa SpilloverFilter Operation Lights FunctionAux1 Name Aux1 FunctionValve3 Name Aux1 InterlockAux1 Freeze Protection Valve3 FunctionValve3 Interlock Valve3 Freeze ProtectionBefore Startup Program Automatic OperationHeater Checkout FCC Statement Industry Canada StatementInterference Limited Warranty-Pool Automation & Chlorination Products Aqua Logic Programming Flow Chart

PS-4 PS-8 specifications

Raypak, a leader in the heating and water temperature control industry, offers a robust line of products featuring state-of-the-art technology and efficiency. Among its notable offerings are the Raypak PS-4 and PS-8 models, which are designed to meet a variety of heating demands in residential and commercial settings.

The Raypak PS-4 and PS-8 are both part of the Performance Series and are designed for versatility. These models utilize high-efficiency gas burners that not only maximize heat output but also minimize fuel consumption. This efficiency is crucial for both cost savings and environmental sustainability, making these heaters an excellent choice for mindful consumers and businesses.

One of the standout features of the PS-4 and PS-8 is their user-friendly digital display, which provides real-time information about system performance. This allows users to easily monitor and adjust settings, ensuring optimal operation at all times. Additionally, these models come equipped with advanced diagnostics that aid in troubleshooting and maintenance, reducing downtime and improving overall system reliability.

The PS-4 model has a heating capacity of up to 400,000 BTU, while the PS-8 boasts an impressive capacity of 800,000 BTU. This wide range of output makes them suitable for a variety of applications, from residential pools to large commercial facilities. Both models feature a durable, rust-resistant cabinet designed to withstand the elements, further enhancing their longevity and performance.

In terms of technology, both heaters are designed with an innovative control system that allows for precise temperature management. Additionally, they feature a built-in fan, which helps distribute heat evenly throughout the space. This ensures that users enjoy consistent temperatures, whether in a pool or spa setting.

The PS-4 and PS-8 models also focus on safety, incorporating multiple safety mechanisms such as high limit sensors and a robust electronic ignition system. These features help prevent issues such as overheating and ensure the system operates safely and reliably.

In conclusion, the Raypak PS-4 and PS-8 models exemplify modern engineering in the heating industry. With their combination of high efficiency, advanced technology, and user-friendly design, they are excellent choices for anyone looking to improve their heating solutions in both residential and commercial applications. Whether for pool heating or spa use, the Raypak heaters promise reliability, performance, and long-lasting service.
Top Page Image Contents