Raypak 122-322 installation instructions Section M PRE-START-UP

Page 43

SECTION M: PRE-START-UP

FILLING SYSTEM-HEATING HEATERS

Fill system with water. Purge all air from the system using purge valve sequence. After system is purged of air, lower system pressure. Open valves for normal system operation, fill system through feed pressure. Manually open air vent on the compression tank until water appears, then close vent.

DOMESTIC HOTWATER HEATERS

Purge all air from system before lighting heater. This can be normally be accomplished by opening a downstream valve.

INSPECT VENTING SYSTEM:

1.Check all vent pipe connections and flue pipe material.

2.Ensure vent terminations are installed per code and are clear of all debris or blockage.

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING:

If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

1.This appliance does have an intermittent pilot. It is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot or burner by hand.

2.BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

3.WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any telephone in your building.

•Immediately call your gas supplier from a neighbor's telephone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire department.

4.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it, call a qualified service technician. Forced or attempted repair may result in a fire or explosion.

5.Do not use this appliance if any part has been under water, immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

6.Check around unit for debris and remove combustible products, i.e. gasoline, etc.

PRE-START-UP CHECK

1.Verify heater is filled with water.

2.Check system piping for leaks. If found, repair immediately.

3.Vent air from system. Air in system can interfere with water circulation.

4.Purge air from gas line up to heater.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operating Installation Instructions Table of Contents Page Product Receipt Section a Before Installing the HeaterRatings and Certifications Model IdentificationHI Delta Component Location General Information Installationcodes Section B Heater InstallationEquipment Base Heater Side 122-322 ModelsHeater Side 120-322 OutdoorinstallationsOutdoor Installation Minimum Clearances Heater ModelCombustion and Ventilation AIR Indoor Units Section C Combustion and Ventilation AIRDirect Combustion AIR Page Reliefvalve Piping LOW Temperature SystemTemperature & Pressure Gauge Section D Water Piping GeneralSection E Hydronic Heating Piping Page Table F-1 Domestic Water Heater Flowrate Requirements Section F Domestic HOT Water PipingSingle Heater Domestic HOT Water with ONE Storage Tank Pooland SPA Water Chemistry Section G Pool HeatingAutomatic Chlorinators and Chemicalfeeders Winterizingyou HeaterGAS Supply Connection Section H GAS Supply ConnectionsGAS Supply Pressure GAS Pressure Regulator Surge Protection Section I Electrical Power ConnectionsCheck the Power Source Check Power SourceMaking the Electrical Connections Field Wiring ConnectionShockhazard Electrical Connections Domestic HOT WaterDefinition ofAppliance Categories Section J Venting ConnectionsTable J-1 Vent Terminal Location General Support of Vent StackVenting Configurations Venting Installation TipsNatural Draft Verticalvent Section J-1 Natural Draft Vertical Venting CategoryNatural Draft Vertical Vent Termination Natural Draft Vertical Venting System InstallationPage HORIZONTALTHRU-WALLVENTING Category III Table Section J-2Horizontal Thru-wall Direct Vent Termination HORIZONTALTHRU-WALLVENTING Table Section J-3 Direct VentHorizontal Thru-wall Direct Vent Termination Verticalventing Table Direct VentVertical Direct Vent Termination Vertical Direct Vent System InstallationSection J-5 Section K Controls Operating Control Ignitionmodule High Limit Manual ResetManual Reset High Limit Flow Switch Ignition Control ModuleLOW Water CUT-OFF LOW Water CUT OFF OptionalWire Diagram Models TIME/TEMPERATURE Relationships in Scalds Section L General Safety PrecautionsSection M PRE-START-UP Turn Off Main Gas Valve Section N Initial START-UPTools Needed Preparation for START-UPYour Hi Delta is tuned START-UPSection O Post START-UP Check Toturn Offgastoappliance Section P OperationSuggested Minimum Maintenance Schedule Section Q MaintenanceInsidecombustionaircontamination Appendix aFig # Heat Exchanger Detail Page Page Page Corporate Headquarters
Related manuals
Manual 44 pages 22.92 Kb

122-322 specifications

Raypak 122-322 is a cutting-edge pool and spa heater designed for optimal performance and efficiency. Known for its robust construction and reliable heating capabilities, this heater has become a preferred choice among pool owners.

One of the standout features of the Raypak 122-322 is its advanced copper fin tube heat exchanger. This innovative technology enhances the heater's efficiency by maximizing heat transfer while minimizing energy consumption. By efficiently circulating the water through the heat exchanger, the Raypak 122-322 quickly raises the temperature, allowing for an enjoyable swimming experience regardless of the weather.

The heater is equipped with a digital control system that allows for precise temperature adjustments. This user-friendly interface makes it easy to set and maintain the desired water temperature, promoting user convenience. The digital controls also provide diagnostic features, which simplify troubleshooting and maintenance, ensuring the heater operates smoothly for years to come.

Safety is a crucial aspect of the Raypak 122-322. It comes with a series of safety features, including a flame rollout switch, high limit switch, and a pressure switch that ensures the unit operates safely under various conditions. This focus on safety provides peace of mind for users, knowing that their heating system is designed with protective measures in place.

The Raypak 122-322 is environmentally friendly, designed to use less energy compared to conventional heating systems. Its efficient performance not only reduces operational costs but also lessens the overall environmental impact, making it a responsible choice for conscious consumers.

With a compact design, the Raypak 122-322 can fit easily into various installation spaces, making it versatile for numerous residential or commercial settings. Additionally, the unit is built with durable materials resistant to corrosion and weather conditions, ensuring longevity and minimal maintenance requirements.

Overall, the Raypak 122-322 stands out in the market due to its advanced features, safety mechanisms, energy efficiency, and ease of use. It exemplifies a perfect blend of innovation and reliability, making it an exceptional option for anyone looking to enhance their pool or spa experience.
Top Page Image Contents