Johnson Controls PC090 THRU 240, PD 180 THRU 240 dimensions Clearances, Rigging

Page 7

430645-YIM-D-0610

Clearances

The unit must be installed with sufficient clearance for air to enter the condenser coils, for air discharge and for servicing access. See Table Table 4 for clearances.

NOTE: Additional clearance is required to remove the compressors out the back of the unit.

Table 4: Minimum Clearances

Clearance Description

Distance in Inches

 

 

Overhead (Top)

120

 

 

Front

36

 

 

Rear

36

 

 

Left Side

30

 

 

Right Side

30

 

 

Bottom1

0

1.In all installations where snow accumulates and winter oper- ation is expected, additional height must be provided to insure normal condenser airflow.

Do not permit overhanging structures or shrubs to obstruct condenser air discharge.

Rigging

Exercise care when moving the unit. Do not remove any packaging until the unit is near the place of installation. Rig the unit by attaching chain or cable slings to the lifting holes provided in the base rails. Spreader bars, whose length exceeds the largest dimension across the unit, MUST be used across the top of the unit.

The unit may be moved or lifted with a forklift. Slotted openings in the base rails are provided for this purpose.

LENGTH OF FORKS MUST BE A MINIMUM OF 60 INCHES.

Spreaders, longer than the largest dimension across the unit must be used across the top of the unit.

Before lifting a unit, make sure that its weight is distributed equally on the cables so that it will lift evenly.

Figure 2: Typical Rigging

Johnson Controls Unitary Products

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 410A General NomenclatureInspection Safety ConsiderationsRenewal Parts Agency ApprovalsPC090 240 and PD180 240 Physical Data Physical DataLimitations InstallationLocation Shipping Operating Corner Weights & Center of GravityRigging ClearancesMinimum Clearances Clearance Description Distance in Inches Compressors Power WiringControl Wiring PhasingFLA Electrical DataRefrigerant Mains Take Adequate PrecautionsLine Sizing Start Installation Thermostat Single Stage Cooling TWO Stage Heating NC120 240 Liquid Line Solenoid Wiring YIM-D-0610 Model Model Piping And Electrical Connections Start-UpCrankcase Heaters Sequence of Operation OperationCooling Sequence Of Operation Dual Stage Heat Pump 4 pipe PD180-240 Dual Stage Heat Pump PC120-240Heating Sequence of Operation Fan Orientation, Control Box End Defrost OperationUnit Control Board PD180 thru 240 Unit Control Board Flash CodesNormal Maintenance TroubleshootingUnit Control Board Option Setup Option Byte SetupCooling Troubleshooting Guide If none of the above correct the error, replace the UCB Johnson Controls Unitary Products Cooling Charging Curves Cooling Charging Curves PC240 Typical PC090 Heat Pump Wiring Diagram Typical Wiring DiagramsTypical PC120 Heat Pump Wiring Diagram Typical PC180 240 Heat Pump Wiring Diagram Johnson Controls Unitary Products York Drive Norman, OK

PC090 THRU 240, PD 180 THRU 240 specifications

Johnson Controls has long been a leader in the HVAC and building efficiency industry, and the Johnson Controls PC090 THRU 240 and PD 180 THRU 240 series of commercial rooftop units exemplify their commitment to innovation and energy efficiency. These units are designed to provide optimal performance for a wide range of commercial applications, ensuring comfortable indoor climates while maintaining energy savings.

One of the standout features of the Johnson Controls PC and PD series is their advanced cooling and heating capabilities. Both series can operate efficiently across a varied range of capacities, typically from 90,000 to 240,000 BTU/h for the PC series and 180,000 to 240,000 BTU/h for the PD series. This versatility allows users to select the most appropriate unit size for their specific needs, optimizing performance without wasting energy.

The technology behind these rooftop units includes advanced inverter-driven compressors that enable variable-speed operation. This feature allows for precise temperature control, resulting in enhanced comfort and reduced energy usage. The units also integrate smart controls that enable easy monitoring and management, ensuring that the HVAC system can adapt to changes in occupancy or external weather conditions.

Another notable characteristic of the Johnson Controls rooftop units is their robust construction and reliability. Designed for outdoor use, these units can withstand harsh weather conditions while maintaining operational efficiency. They are equipped with corrosion-resistant materials and protective enclosures to prolong the life of the equipment.

The units are also engineered with eco-friendliness in mind, utilizing refrigerants with low global warming potential to minimize their environmental impact. Furthermore, their energy-efficient designs often qualify for various energy incentives, providing businesses an additional return on investment.

Ease of installation and maintenance is another hallmark of the PC and PD series. With a modular design, these units can be easily transported and installed. Maintenance tasks are simplified, allowing facility management teams to perform regular service checks efficiently and effectively.

Overall, the Johnson Controls PC090 THRU 240 and PD 180 THRU 240 series stand out in the commercial HVAC market due to their flexibility, advanced technology, and dedication to energy efficiency and environmental responsibility. These units not only meet modern energy codes but also contribute to a sustainable future with their innovative features and reliable performance.
Top Page Image Contents