GE AG_14, MG_24 installation instructions Preparing to install the air conditioner

Page 9

Preparing to install the air conditioner.

Read these instructions completely and carefully.

Before You Begin

Safety Instructions

NOTE TO INSTALLER: Leave these instructions with the air conditioner after installation is completed.

NOTE TO CONSUMER: Keep this Owner’s Manual and Installation Instructions for future use.

IMPORTANT NOTES:

For personal safety, this air conditioner must be properly grounded.

It is important to have the wall outlet and circuit checked by a qualified electrician if there is any doubt as to whether a proper ground exists.

Follow National Electric Codes (NEC) and/or local codes and ordinances.

CAUTION:

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of this air conditioner.

Aluminum house wiring may present special problems—consult a qualified electrician.

Operating Instructions

Electrical Requirements

Some models require 115/120-volt a.c., 60 Hz grounded outlet protected with

a 15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.

Tools You Will Need

■ Phillips-head screwdriver

■ Pencil

■ Flat-blade screwdriver

■ Level

■ Ruler or tape measure

■ Hammer

■ Scissors or knife

 

9

Installation Instructions Troubleshooting Tips Consumer Support

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Write the model and serial numbers here Air ConditionersSafety Precautions USE of Extension Cords -115-Volt models only Controls Remote ControlFAN Mode Cool ModeVent Control Air Direction Up and DownTemp Controls Mode ControlsCooling Descriptions For Normal Cooling-SelectHIGH Cool or MEDAir Direction Side-to-Side Instructions Operating Vent ControlGrille and Case Care and cleaning of the air conditionerOutdoor Coils Air FilterRead these instructions completely and carefully Preparing to install the air conditionerParts Included Window Installation InstructionsStorm Window Requirements Window RequirementsRemove the Air Conditioner From the Case Prepare the Window and the CasePrepare the Window Install the Case in the WindowInstall the Air Conditioner in the Case Before you call for service… Normal Operating Sounds We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Will Replace Air Conditioner WarrantyWhat GE Will Not Cover For The PeriodParts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design Studio

AG_14, MG_24 specifications

The GE AG_14 and MG_24 are two advanced electric power generation systems developed by General Electric (GE) that showcase the innovative approaches the company is known for in the energy sector. These systems are engineered to meet the demands of modern energy requirements, leveraging cutting-edge technologies and features to enhance performance and efficiency.

The GE AG_14 is a gas turbine power generation system designed for high efficiency and low emissions. It is built to operate on a wide range of fuels, including natural gas and biofuels, making it versatile for various energy applications. One of the standout features of the AG_14 is its advanced combustion technology, which minimizes nitrogen oxide (NOx) emissions while optimizing fuel consumption. Additionally, the AG_14 incorporates advanced materials and design principles to improve durability and maintenance intervals, reducing overall lifecycle costs.

The system is equipped with integrated digital controls that allow for real-time monitoring and precise management of operations. This helps optimize performance and improve reliability, ensuring that the energy output is consistent and meets grid requirements. The modular design of the AG_14 allows for easy transportation and installation, making it suitable for both temporary and permanent setups.

On the other hand, the GE MG_24 is a multi-generational distributed power solution aimed at providing reliable energy in remote or off-grid locations. Its hybrid capability enables it to function alongside renewable energy sources like solar and wind, effectively contributing to a greener energy mix. The MG_24 features energy storage integration, allowing for smooth operation during periods of fluctuating energy demand and supply.

The MG_24 system is designed with robust telemetry and internet of things (IoT) capabilities, enabling operators to manage the unit efficiently from a distance through a centralized control platform. This enhances operational visibility and aids in predictive maintenance, which helps minimize downtime.

Characteristics of both the AG_14 and MG_24 systems highlight GE's commitment to sustainability, efficiency, and adaptability in today's energy landscape. With these innovative solutions, GE continues to play a pivotal role in shaping the future of power generation, addressing the challenges of energy transition while promoting economic growth and environmental stewardship.
Top Page Image Contents