GE ASQ14, ASV10, ASM10*, ASM08*, ASQ12, ASQ10 Power Outage Recovery Feature, Cool Mode, Fan Mode

Page 5

ge.com

Additional controls and important information.

Do Not Operate in Freezing Outdoor Conditions

This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.

When the air conditioner is turned on, it will automatically start in the setting last used.

Power Outage Recovery Feature

In the case of a power outage or interruption, the

Sleep features will reset to the original setting.

unit will automatically re-start in the settings last

You may need to set a new time if desired.

used after the power is restored. The Timer and

 

 

 

Safety Instructions Operating

Cool Mode

Use the Cool mode with High (3), Med (2) or Low (1) fan for cooling. Use the Increase ▲ / Decrease ▼ pads to set the desired temperature between 64°F and 86°F in 1°F increments.

A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling—Select the Cool mode and High (3) or Med (2) fan with a middle set temperature.

For Maximum Cooling—Select the Cool mode and High (3) fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the Cool mode and Low (1) fan with a middle set

temperature.

NOTE: If you switch from a Cool setting to Off or to

a fan setting, wait at least 3 minutes before switching back to a Cool setting.

Instructions Installation Instructions

Fan Mode

Use the Fan at High (3), Med (2) or Low (1) to provide

Since fan only settings do not provide cooling,

air circulation and filtering without cooling.

a temperature setting will not be displayed.

Vent Control (on some models)

The vent control is located on the inside of the air louvers in the lower right corner.

When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.

To open the vent, push the lever to the right. To close it, push it to the left.

OR

To open the vent, push the lever to the right. To close it, push it to the left.

Troubleshooting Tips

Air Direction—Up and Down (on some models)

Fingertip pressure on the horizontal louvers adjusts

OR

the air direction up or down.

Air Direction—Side-to-Side (on some models)

 

On some models, the side-to-side air direction is

OR

adjusted by the louver levers or by grasping and

 

moving the inner vertical louvers.

 

5

Consumer Support

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Write the model and serial numbers here Model # Serial # Air ConditionersDo not use an adapter plug with this appliance Consumer Support Troubleshooting TipsGe.com USE of Extension CORDS-115-Volt models onlyConsumer Remote ControlCool Mode Power Outage Recovery FeatureFan Mode Air Direction-Up and Down on some modelsTroubleshooting Tips Installation Instructions Operating Air Direction-Side-to-Side Safety InstructionsHow to Insert the Batteries Care and cleaning of the air conditionerGrille and Case Outdoor CoilsTools YOU will Need Before YOU BeginElectrical Requirements Parts Included Window Installation InstructionsRemove the Front Grille if Attached Window RequirementsStorm Window Requirements Prepare the Case Remove the AIR Conditioner from the CaseInstall the Case in the Window Install the CaseInstall the Security Bracket and the Foam TOP Window Gasket Install the AIR Conditioner in the Case Finish the Wall Opening Through-the-Wall Installation Instructions-OptionalNormal Operating Sounds Troubleshooting Tips…We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Will Replace GE Air Conditioner WarrantyWhat Is Not Covered Parts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design StudioAcondicionadores de Aire Seguridad ¡ADVERTENCIA Solucionar problemas Apoyo al consumidorLas funciones y el aspecto pueden variar Control remotoFunción de recuperación de pérdida de energía InstalaciónModo Cool Frio Modo de FAN VentiladorInterruptor ON/OFF Control de Mode ModoInterruptor de Fan Ventilador Control de Mode/Temp Modo/TempDirección del aire-de lado a lado Seguridad Cuidado y limpieza del acondicionador de airePrecaución no Opere el Requisitos Electricos Antes DE IniciarPartes Incluidas Herramientas QUE Usted NecesitaráRequisitos DE UNA Ventana DE Tormentas Requisitos Para LA VentanaRetire EL Acondicionador DE Aire DE LA Caja Retire LA Parrilla Frontal SI Está PegadaInstale LA Caja EN LA Ventana Prepare LA CajaInstale EL Acondicionador DE Aire EN LA Caja Instale LA CajaImportante Instrucciones de instalación a través de la pared-opcionalExterior Termine LA Abertura EN LA ParedSolucionar problemas Sonidos de operación normales Operación Garantía de su acondicionador de aire de GEGE reemplazará Lo que no está cubiertoSolicite una reparación Apoyo al Consumidor Página Web de GE AppliancesGarantías ampliadas Piezas y accesorios

ASQ14, ASQ10, ASQ12, ASM08*, ASM10* specifications

The GE ASV10, ASM08*, ASQ14, ASQ12, and ASM10* are part of General Electric's advanced range of automation and control solutions designed for various industrial applications. These products are notable for their high performance, flexibility, and the ability to meet diverse operational requirements across several sectors.

The ASV10 is a versatile automation solution offering significant scalability options. It integrates seamlessly with multiple device types and supports various communication protocols, enabling users to create comprehensive control systems tailored to their specific needs. This feature facilitates easy integration into existing systems while allowing for future expansions.

ASM08*, on the other hand, is known for its rugged design and robust performance in challenging environments. It is equipped with advanced processing capabilities that enhance reliability in data management and real-time decision-making. The ASM08* supports a wide range of I/O configurations, making it an ideal choice for applications that require high adaptability.

Moving to the ASQ14 and ASQ12, these models are characterized by their sophisticated quality control features. They are designed to excel in environments where precision and reliability are paramount. These systems feature advanced data analytics, allowing operators to monitor processes in real-time and make informed decisions based on accurate information. The ASQ series also includes built-in diagnostic tools that facilitate troubleshooting and minimize downtime.

The ASM10* is another noteworthy addition, emphasizing high-speed processing and efficient energy management. This model supports cutting-edge technologies such as machine learning algorithms, allowing for predictive maintenance and enhanced operational efficiency. Its architecture is designed to optimize resource use, ensuring that users can maintain productivity while reducing operational costs.

In summary, the GE ASV10, ASM08*, ASQ14, ASQ12, and ASM10* showcase a commitment to innovation and excellence in automation technology. With features that cater to a wide array of industrial challenges — from scalability and integration to precision and efficiency — these products stand out as reliable solutions for modern automation needs. Together, they represent GE's dedication to advancing industry standards and providing tools that empower organizations to succeed in a competitive landscape.
Top Page Image Contents