GE AGM24 operating instructions Prepare the Window, Install the Case in the Window

Page 11

Installation Instructions

5PREPARE THE WINDOW

ALoosely attach the sill brackets to the support brackets using the 2 carriage bolts and 2 lock nuts.

Support bracket

Carriage bolt

Lock nut

Sill bracket

BOpen the window and mark the centerline of the window stool. Measure and mark 11″ to the left and right of the centerline.

Centerline

″ 11 ″ 11

6INSTALL THE CASE IN THE WINDOW

AAlign the inside edge of the sill brackets with the 11″ marks from the centerline and attach them to the window sill using 2 type B screws on each side.

BCarefully place the case on the window stool aligning the center front on the bottom with the centerline marked on the window stool. Close the window making sure the window sash is behind the top mounting rail.

CUsing the larger diameter hole in the case, attach the brackets to the case using two

type D screws and 2 lock nuts on each side.

6INSTALL THE CASE IN THE WINDOW (CONT.)

DAdjust the carriage bolts and the lock nuts in each support so that the case is installed with a slight tilt to the outside. Use a level; about 1/3 bubble will be the correct case slant to the outside. Tighten the bolts.

CAUTION: DO NOT drill a hole in the base pan. The unit is designed to operate with approximately 1/2 ″ of water in the base pan.

ESecure the case to the window stool by using 3 type B screws.

FPull the accordion panels to each window sash track. Attach them on each side to the window sash and the window stool using 4 type C screws.

11

Image 11

Contents Write the model and serial numbers here Model # Serial # Air ConditionersInstallation Consumer Support Troubleshooting TipsGe.com Installation InstructionsInstructions Power Outage Recovery FeatureRemote Control About the controls on the air conditionerTips Consumer Support Air Filter Care and cleaning of the air conditionerGrille and Case Outdoor CoilsTools YOU will Need Before YOU BeginElectrical Requirements Parts Included Installation InstructionsStorm Window Requirements Window RequirementsPrepare the Window and the Case Remove the AIR Conditioner from the CasePrepare the Window Install the Case in the WindowInstall the AIR Conditioner in the Case Install the AIR Conditioner in the CaseTroubleshooting tips Normal Operating Sounds We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Will Replace GE Air Conditioner WarrantyWhat Is Not Covered Extended Warranties Schedule ServiceParts and Accessories Consumer Support GE Appliances WebsiteAcondicionadores de Aire Operación Instalación ¡ADVERTENCIAApoyo al consumidor Solucionar problemasOperación Función de recuperación de pérdida de energía Acerca de los controles en el acondicionador de aireSeguridad Apoyo alSolucionar Precaución no Opere el Instalación Apoyo al consumidor Solucionar problemasCuidado y limpieza del acondicionador de aire Requisitos Eléctricos Antes DE IniciarPartes Incluidas Herramientas QUE NecesitaráRequisitos DE UNA Ventana DE Tormentas Requisitos Para LA VentanaRetire EL Acondicionador DE Aire DE LA Caja Prepare LA Ventana Y LA CajaInstale LA Caja EN LA Ventana Prepare LA VentanaInstale EL Acondicionador DE Aire EN LA Caja LA VentanaSeguridad Operación Instalación Solucionar problemasNo está funcionando Se acumula aguaEn la bandeja La función deSonidos de operación normales Notas Lo que no está cubierto Garantía de su acondicionador de aire de GESeguridad Operación GE reemplazaráPiezas y accesorios Apoyo al consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadas