Through-the-Wall Installation Instructions-Optional

Through-the-Wall Installation Instructions—Optional

The case may be installed through-the-wall in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Except for the V-support assemblies (included), obtain all materials locally for mounting the air conditioner through-the-wall.

1IMPORTANT

Through-the-wall installation is not appropriate if any of the side or top louvers in the case will be obstructed by the wall.

All side and top louvers in the case must project on the outdoor side of the wall.

The room side of the case must project into the room far enough to maximize the balance of the unit.

The case must be installed level from side- to-side and with a slight tilt from front to rear. Use a level; no more than a 1/2 bubble will be the correct case slant to the outside.

Lintel angle is required to support bricks or blocks above opening.

Flashing is required and should extend the length of the opening to ensure no inside cavity leakage occurs.

ARemove the air conditioner from the case. For specific instruction, refer to the Window Installation Instructions.

BMake certain that a wall receptacle is available close to the hole location or make arrangements to install a receptacle.

CPlace the case in the wall opening and place wood support strips between the case bottom and the flashing on both sides of the bottom rail. They should be the same height as the bottom rail and the same length as the wall opening.

1IMPORTANT (cont.)

DSecure with 14 wood screws anchored at least an inch into the wall support structure.

NOTE: Drill pilot holes, if necessary, for proper installation. If the frame is oversized, use shims to prevent case distortion.

EInstall the V-supports. See the INSTALL THE CASE IN THE WINDOW section in the Window Installation Instructions.

2FINISH THE WALL OPENING

ACaulk all four sides on the outdoor side of the case to prevent moisture from getting through to the interior wall. Use of flashing (drip rail) will further prevent water from dripping inside the wall and down the outside of the building.

		Plaster line
	Lintel angle
	Caulking	Trim molding
		(if desired)
	OUTSIDE	INSIDE
		INSIDE
	Air louvers
	(top and	Bottom rail
	sides must	Bottom rail
	sides must
	project on the
	outdoor side
	of the wall)

Wood filler and caulking (above and below the flashing)

V-supports

Case Bottom

Flashingbottom rail (Drip rail)

Flashing (Drip rail)

Wood support strips

BPlace the air conditioner into the case.

For specific instruction, refer to the Window Installation Instructions.

AEH18, AEM18, AEH25, AEM25 specifications

General Electric (GE) has made significant strides in the evolution of its gas turbine technology with the introduction of the AEM18*, AEM25*, AEH25*, and AEH18* series. These models are engineered to meet the growing demands for efficient, reliable, and environmentally responsible energy generation.

The AEM18* and AEM25* models focus on advanced aerodynamics and materials science to deliver high efficiency and performance. These turbines utilize a state-of-the-art combustion system that enables low emissions operation while maintaining operational flexibility. The AEM series is renowned for its capabilities in combined cycle applications, offering a high power-to-weight ratio which enhances overall system efficiency.

The AEH25* and AEH18* models build upon the advanced technology established in the AEM series but introduce enhancements aimed at heavy-duty and industrial applications. With innovative design modifications, including improved rotor dynamics and robust cooling techniques, these turbines achieve excellent reliability and availability. The AEH series is designed with high operational flexibility, capable of handling high load variations while providing consistent performance.

All four turbine models share GE's commitment to utilizing advanced digital technologies, including the Predix platform, which harnesses the power of analytics. This technology allows operators to monitor performance in real time, predict maintenance needs, and optimize operational parameters, resulting in reduced downtime and improved efficiency.

In terms of characteristics, the AEM and AEH series turbines are characterized by their modular design, which simplifies installation and maintenance processes. This design allows for easier upgrades and retrofits, ensuring that customers can adapt their systems to future technological advancements.

The environmental impact of these gas turbines cannot be understated. Both the AEM and AEH series are designed to meet rigorous emissions standards, showcasing GE's commitment to sustainability. With reduced greenhouse gas emissions and the capacity to integrate with renewable energy sources, these turbines serve as a key component in the transition to cleaner energy systems.

In summary, the GE AEM18*, AEM25*, AEH25*, and AEH18* turbines represent a culmination of innovative engineering, advanced technology, and a focus on environmental sustainability, making them suitable choices for a variety of energy generation applications in today's dynamic energy landscape.