Atlas MLGC240W, MLGC240B manual Troubleshooting Guide, Symptom Possible Cause

TROUBLESHOOTING GUIDE

If you experience a problem with your Light Control, first follow this guide. For additional assistance write to:

Atlas Lighting Products, Inc. • Customer Service Department • P.O. Box 2348 • Burlington, NC 27216

SYMPTOM	POSSIBLE CAUSE
Lights will not	1. Light switch is turned off.
come on.	2. Flood light is loose or
		burned out.
	3.	Fuse is blown or circuit breaker
		is turned off.
	4.	Daylight turn-off is in effect (Re-
		check after dark).
	5.	Incorrect circuit wiring, if this is a
		new installation.
	6.	Re-aim the sensor to cover de-
		sired area.
Lights come on	1. Light Control may be installed in
in daylight.		a relatively dark location.
	2.	Light Control is in Test. (Set
		control switch to an ON-TIME
		position).
Lights come on	1. Light Control may be sensing
for no apparent		small animals or automobile traf-
reason.		fic (Re-aim sensor).
	2.	Range is set too high. (Reduce
		Range).
	3.	Dual Light Level is on.

SYMPTOM	POSSIBLE CAUSE
Lights stay on	1. A flood lamp is positioned too close
continuously.		to the sensor or pointed at nearby
		objects that cause heat to trigger the
		sensor. (Reposition the lamp away
		from the sensor or nearby objects).
	2. Light Control is pointed toward a heat
		source like an air vent, dryer vent, or
		brightly-paintedheat-reflectivesurface.
		(Reposition sensor. Reduce Range).
	3.	Light Control is in Manual Mode.
		(Switch to Auto.)
Lights flash	1.	Heat or light from the lamps may be
on and off.		turning the Light Control on and off.
		(Reposition the lamps away from the
		sensor).
	2.	Heat being reflected from other ob-
		jects may be affecting the sensor.
		(Reposition sensor).
	3.	Light Control is in the Test mode and
		warming up. (Flashing is normal un-
		der these conditions. Turn Boost off.)
	4.	Light may be leaking through the
		floodlamp reflectors. (Make sure the
		metal lamp protectors are installed).
Lights flash	1.	Sensor is detecting its own lights
once, then		(Reposition lamps to keep area be-
stay off in		low sensor relatively dark).
Manual Mode.

FIVE YEAR LIMITED WARRANTY

Atlas Lighting Products, Inc. warrants against defects in materials or workmanship for a period of five years from the date of purchase for use, and agrees to repair or, at our option, replace a defective unit without charge for either parts or labor. IMPORTANT: This warranty does not cover damage resulting from accident, misuse of abuse, lack of reasonable care, the affixing of any attachment not provided with product, alteration of any attachments factory installed, loss of parts or subjecting the fixture to any but the specified electrical service. This warranty does not cover failure of the bulb due to accidents, abuse, misuse, vandalism, power surges, and acts of nature such as lightning damage. No responsibility is assumed for any special incidental or consequential damages. Damages occurring during transit are not covered by this warranty-including UPS shipments. To obtain warranty service, mail sales receipt as proof-of-purchase, date and a brief explanation of the nature of the defect, to the address listed below. You will receive, by mail, a Return Goods Authorization number and full instructions for returning defective merchandise. All returned goods must be accompanied by a Return

Goods Authorization number issued by Atlas Lighting Products, Inc.

NOTE: No other warranty, written or verbal, is authorized by Atlas Lighting Products, Inc. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion and limitations may not apply to you.

For information regarding replacement parts please write to:

Atlas Lighting Products, Inc.

Attn: Customer Service Department

P.O. Box 2348

Burlington, NC 27216

-4- 598-1094-01