Panasonic SC-ZT2 warranty Error messages, Using with headphones, Specifications

Error messages

Display		Check point/Cause/Countermeasure		Pages
CANCEL MUTE FUNCTION (Scrolling)	•	The test signal is not output while muting is on. Cancel muting for operation.		20
MUTE (Blinking)	•	This is always displayed while muting is on.		20
NOT POSSIBLE FOR	•	You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic	for dual	—
THIS INPUT SOURCE (Scrolling)		sounds.
NOT POSSIBLE FOR	•	You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic	effect with	17
THIS PCM SOURCE (Scrolling)		PCM signals with sampling frequency of over 48 kHz.
NOT POSSIBLE WHEN USING	•	You cannot use the sound field effects when using headphones.		25
HEADPHONES (Scrolling)
	•	Set the same remote control code for this main unit and remote control. When “REMOTE 2 ”		24
REMOTE 2		is displayed, set the code to “2 ” on the remote control in step 4 of procedure “When other
		equipment (mini component system, AV amp, etc.) manufactured by Panasonic operates
REMOTE 1
		with the remote control operations of this system”. When “REMOTE 1 ” is displayed, set the
		code to “1 ” on the remote control in step 4 in the same way.
SWITCH OFF POWER	•	While “F70 ” is displayed, all operations but turning ON/OFF operation are not		—
(Scrolling)		available. Turn off the system, unplug the AC power supply cord, and consult your dealer.
TURN OFF DTS FIX MODE	•	When each input is fixed to DTS (DTS FIX), the sound field effects cannot be		24
(Scrolling)		canceled even if you press [–SETUP, OFF]. Cancel DTS FIX.
U701	•	The equipment connected by the HDMI cable is not compatible with this system’s copyright protection technology.		—
	•	A problem has occurred with the HDMI connection. Try the following to correct		—
		the problem. Consult your dealer if the error code remains on the display.
U703		– Turn the connected equipment off and on again.

–Disconnect the HDMI cable then reconnect it.

–Do not connect more than 2 sets of equipment to this system’s output.

U704	• The system received incompatible video signals through HDMI connection.			—
	Check the settings of the connected equipment.
Using with headphones
Turn down the volume closest to the minimum value.			Note
• Plug type: ø 3.5 mm (1/8 in.) stereo mini plug		•	Avoid listening for prolonged periods of time to prevent hearing
	W (Headphone) jack		damage.
		•	Multi-channel signals are forcibly converged to 2-channel and
			output. (2CH MIX)
	Headphones		However, for DVD audio, the front left and right signals are output.
	(not included)

headphones/Specifications

Specifications

MAIN UNIT
g PRE AMPLIFIER SECTION
Input sensitivity / Input impedance
TV, AUX3	600 mV / 47 kΩ
S/N ratio (IHF A)
BD/DVD, TV, AUX1,
AUX2 (Digital Input)	80 dB (IHF '66)
Tone controls
BASS	50 Hz, + 6 to –6 dB
TREBLE	20 kHz, + 6 to – 6 dB
Input/Output terminal
Audio Input
Analog Input ( TV, AUX3 )		2
Optical Digital Input	( TV, AUX2 )	2
Audio Output
Audio Output ( Front L/R, Surround L/R )		4
Subwoofer Output		1
Headphone Output	( 16 to 64 Ω )	1
Video/Audio
HDMI Input ( BD/DVD, AUX1 )		2
HDMI Output ( TO TV (ARC))		1

This system supports “HDAVI Control 4” function.

g MAIN UNIT GENERAL
Power supply	AC 120 V, 60 Hz
Power consumption		16 W
In standby condition		0.5 W
In standby condition ( HDMI off mode )		0.2 W
Dimensions ( W x H x D )	430 mm x 59 mm x 262 mm
	(16-15/16" x 2-5/16" x 10-5/16")
Mass [ Weight ]	Approx. 2 kg (4.4 lb.)
Operating temperature range	0°C to 40 °C (32°F to 104 °F)

Operating humidity range 20 % to 80 % RH (no condensation)

g WIRELESS SECTION
Frequency of the using band	2.4000 GHz to 2.4835 GHz
Number of using channels	3
The reaching distance	15 m (49 ft)∗1

∗1 It is under the condition as follows.

At same room indoor, there is not an obstacle between the main unit and the speaker.

And installing a main unit in the position with equal to or more than 50 cm height.

SPEAKER

g POWER AMPLIFIER SECTION∗2
RMS output power
10 % total harmonic distortion
Woofer Speaker ch	60 W (100 Hz, 3	Ω)
Mid High Speaker ch	20 W (1 kHz, 8	Ω)
System Total Power∗3	160 W (80 W x 2)

FTC output power

1.0 % total harmonic distortion

50 Hz to 250 Hz	Woofer Speaker ch 37	W (3 Ω)
250 Hz to 20 kHz Mid High Speaker ch 13		W (8 Ω)
System Total Power∗3	100 W (50 W x 2)

g SPEAKER SECTION∗2

2-way 5 speakers system (Bass reflex type)

Woofer part	12 cm cone type x 1
Mid High part	2.4 x 10 cm flat type x 4
g SPEAKER GENERAL∗2
Power supply	AC 120 V, 60 Hz
Power consumption	20 W
Wireless Link Standby	0.8 W
In Standby condition	0.1 W
Dimensions ( W x H x D )	290 mm x 1231 mm x 290 mm
	(11-13/32" x 48-15/32" x 11-13/32")
Mass [ Weight ]	Approx. 3.9 kg (8.6 lb.)

Operating temperature range 0°C to 40°C (32°F to 104°F) Operating humidity range 20 % to 80 % RH (no condensation) ∗2: per 1 speaker

∗3: use 2 speakers

Note: 1. Specifications are subject to change without notice.

2.Total harmonic distortion is measured by the digital spectrum analyzer.

3.Total harmonic distortion is measured by using AES17 filter.

Troubleshootingother informationand Error messages/Using with

25

VQT2R70